manualshive.com logo in svg

Appear TV DC100 Series, Product User Manual

The Appear TV DC100 Series is a high-quality broadcasting solution that revolutionizes the way you consume media. To ensure a seamless user experience, we offer a comprehensive and easy-to-understand Product User Manual. Download the manual for free at manualshive.com to unlock the full potential of your Appear TV DC100 Series equipment.

Share
Download
background image

 

 

 

APPEAR AS

 

Confidential 

12/352

 

2.1.2

 

1RU

 

C

HASSIS 

XC5100 

The 1RU chassis for the XC5100 holds of a total of 6 slot positions plus a slot for the Switch/IP module.  The 
Switch/IP module is inserted in the front of the chassis, while the modules for the other 6 positions are inserted 
in the back of the chassis. All modules are hot-swappable, including power supplies and the fan module in front. 

The 1RU chassis is equipped with dual 400W AC or 500W DC power supplies 

Figure 2.5 shows the front and rear view of the 1RU chassis including a mandatory switch module, power supply 
connectors, and module slots. 

 

XC5100

DATA A

DATA B

CONTROL

 

Slot #1

Slot #2

Slot #3

Slot #4

Slot #5

Slot #6

 

Figure 2.5 - 1RU chassis for XC5100 with dual power, switch module and available slots; front and rear view.

 

This chassis can hold 2 power supply modules for redundancy purpose 

2.1.2.1

 

Ventilation 

This XC5100 has forced air flow from front to back allowing for multiple units to be stacked above each other 
with no space in between. However, adequate space must be provided in front of and behind the unit for 
effective ventilation.   

The XC5100 has 6 fans in front.  Fan speed is temperature controlled. If one fan fails, remaining fans will increase 
speed to compensate.  The whole Fan module, containing all 6 fans, can be hot swapped.  If, during fan module 
replacement, the temperature on the inserted modules exceeds a certain critical temperature, the unit will shut 
down, to prevent damage of the inserted modules. 

2.1.2.2

 

Replacing the power supply module 

This 1RU chassis can be installed with one or two hot swappable power supply modules. The modules can be 
exchanged from the rear of the unit. The chassis delivered with a single power module can be updated by 
acquiring additional power module. 

If power is lost in one of the Power supplies, the other can feed the entire chassis. It is recommended to connect 
each input power at different circuits. 

2.1.3

 

S

AFETY 

C

ONSIDERATIONS

 

The unit 

must

 be connected to a grounded power connection.  The power input connector) is a 

disconnect 

device

.   To remove the power from the device, the power cables needs to be physically removed from the 

power input connector. 

Summary of Contents for DC100 Series

































































































































































































































































































































































Reviews:

No comments

Related manuals for DC100 Series

Ramsey Electronics SC1 Manual preview
SC1
Brand: Ramsey Electronics Pages: 20
DANE-ELEC SO ROAD MOVIE CAR PACK Quick Start Manual preview
SO ROAD MOVIE CAR PACK
Brand: DANE-ELEC Pages: 14
DANE-ELEC SO ROAD MOVIE Datasheet preview
SO ROAD MOVIE
Brand: DANE-ELEC Pages: 2
DANE-ELEC SO WORLD TV - Quick Start Manual preview
SO WORLD TV -
Brand: DANE-ELEC Pages: 16
DANE-ELEC SO G-STREAM - Quick Start Manual preview
SO G-STREAM -
Brand: DANE-ELEC Pages: 16
DANE-ELEC SO SPEAKY - Datasheet preview
SO SPEAKY -
Brand: DANE-ELEC Pages: 2
DANE-ELEC SO XSTREAM FULL HD - Datasheet preview
SO XSTREAM FULL HD -
Brand: DANE-ELEC Pages: 2
G-Lab M4L User Manual preview
M4L
Brand: G-Lab Pages: 16
YOKOGAWA 3142 Instruction Manual preview
3142
Brand: YOKOGAWA Pages: 13
Nedap PowerRouter PR50S Installation And Operating Manual preview
PowerRouter PR50S
Brand: Nedap Pages: 64
Mitsubishi FR-A7NC Instruction Manual preview
FR-A7NC
Brand: Mitsubishi Pages: 106
Velleman PI3000B - 24V User Manual preview
PI3000B - 24V
Brand: Velleman Pages: 48
Eminent EM7680 Manual preview
EM7680
Brand: Eminent Pages: 31
Linear Technology DC2312A-A Demo Manual preview
DC2312A-A
Brand: Linear Technology Pages: 22
Microtek IN-1400VA User Manual preview
IN-1400VA
Brand: Microtek Pages: 17
tams elektronik 22-01-090 Manual preview
22-01-090
Brand: tams elektronik Pages: 26
I-novative Factory-Link-SPE-M User Manual preview
Factory-Link-SPE-M
Brand: I-novative Pages: 12
J-Tech Digital JTD-673 User Manual preview
JTD-673
Brand: J-Tech Digital Pages: 34

Brands by name

Popular brands

Load more brands