Anmax CM-520 User Manual Download Page 325

Page: 325 / 348

Enter 309 End

*/$%ENTR* *ZEND*

Configuring Symbology

8-18.

GS1 Databar Limited(RSS Limited)

8-18-1.

Enable/Disable RSS Limited

Scan the appropriate barcode to determine whether or not to enable RSS Limited.

8-18-2.

Transmit Application ID

Scan the appropriate barcode to determine whether or not to transmit Application ID,

8-18-3.

Transmit Symbology ID

Scan the appropriate barcode to determine whether or not to transmit Symbology ID,

]e0

8-18-4.

Transmit Check Digit

Scan the appropriate barcode to determine whether to transmit the check digit.

*F0001*

Enable

F0001

*F0000*

Disable

F0000

*F0041*

Enable

F0041

*F0040*

Disable

F0040

*F0051*

Enable

F0051

*F0050*

Disable

F0050

*F0070*

Disable

F0070

Summary of Contents for CM-520





























































































































































































































































































































































Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands

Anmax CM-520, User Manual

Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands