Anmax CM-520 User Manual Download Page 209

Page: 209 / 348

Enter 193 End

*/$%ENTR* *ZEND*

Setting up your Operation Modes

7-4-3-12.

Enable/Disable Date Information

Scan the appropriate barcode to determine whether or not to transmit date information

along with the decoded message.

7-4-3-13.

Enable/Disable Time Information

Scan the appropriate barcode to determine whether or not to transmit time information

along with the decoded message.

7-4-3-14.

Reject Same

Scan the appropriate label to configure your scanner not to decode the barcode which is

exactly the same to your previous scan. Scan

Enable

label to avoid possibility of

consecutively reading the same barcode twice by accident. Otherwise, by default the

scanner will decode barcodes without leaving out those unqualified barcodes.

7-4-3-15.

Enable/Disable Barcode Verification

Scan the appropriate barcode to enable or disable barcode verification mechanism which

allows the decoder to decode the scanned data repetitively for better accuracy. By default,

*C6130*

Disable

C6130

*C6131*

Enable

C6131

*C6140*

Disable

C6140

*C6141*

Enable

C6141

*C6200*

Disable

C6200

*C6201*

Enable

C6201

Summary of Contents for CM-520





























































































































































































































































































































































Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands

Anmax CM-520, User Manual

Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands