Anmax CM-520 User Manual Download Page 150

Page: 150 / 348

Enter 134 End

*/$%ENTR* *ZEND*

Setting up your Operation Modes

7-2-3-22.

Set Suffix Code

In the process of transmitting data, Suffix Code is normally interposed between barcode

data and Postamble Code as a user-defined string to format the output data. By binding

this configurable parameter with parameter value which is identifiable for you to achieve

the attempt, Suffix Code is meant to identify the difference among lines, whereas

functionality of Postamble Code is to arrange the data format by breaking the

transmission line. Please follow the below steps to configure Suffix Code.

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

SuffixChar

barcode to configure Suffix Code.

(3)

Please refer to ASCII Code Table and Decimal/Hexadecimal Table in the

appendix to scan hexadecimal value barcodes representing the desired string

which has to be at most 8 characters in length. For instance, to set suffix code to

be “EFGH”, scan

4, 5, 4, 6, 4, 7, 4,

and then

to assign the specified hexadecimal

value "45464748".

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

*BB8E5*

SuffixChar

BB8E5

(Length: 8 digits)

Summary of Contents for CM-520





























































































































































































































































































































































Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands

Anmax CM-520, User Manual

Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands