Anmax CM-520 User Manual Download Page 229

Page: 229 / 348

Enter 213 End

*/$%ENTR* *ZEND*

Configuring Symbology

8-3-12.

Set Sub Code ID for UPC-E

A user-defined Sub Code ID functions as an identity for some specific types of symbologies

to verify whether or not its exclusive feature is enabled. In the case of UPC-E, this parameter

is used to identify those altered UPC-E barcodes which are adapted in compliance with

UPC-A encoding standards. When the conversion function in

Section 8-3-4

is enabled, the

device will send out Sub Code ID rather than the original Code ID as part of transmitted

data.

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

Sub

barcode to tailor Code ID for UPC-E to your needs.

(3)

Please refer to ASCII Code Table and Decimal/Hexadecimal Table in the appendix

to scan hexadecimal value barcodes representing the desired string which has to be

at most 2 characters in length. For instance, to set its Code ID to be “Au”, scan

4, 1,

and then

to assign the specified hexadecimal value “4175”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

(Length: 2 digits)

*D3EE3*

Sub ID

D3EE3

Summary of Contents for CM-520





























































































































































































































































































































































Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands

Anmax CM-520, User Manual

Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands