Anmax CM-520 User Manual Download Page 190

Page: 190 / 348

Enter 174 End

*/$%ENTR* *ZEND*

Setting up your Operation Modes

7-4-1-21.

Set Bluetooth Address

Mac Address information is required for the scanner to locate the Bluetooth devices,

except for Bluetooth dongle A302/A303, for establishment of a Bluetooth connection.

Please associate this parameter with the Bluetooth address of the Bluetooth device.

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

BtMacAddr

barcode to configure Mac Address.

(3)

Please refer to ASCII Code Table and Decimal/Hexadecimal Table in the

appendix to scan hexadecimal value barcodes representing the desired string

which has to be 12 characters in length. For instance, to set Bluetooth Address to

be “001C97FE16EC”, scan

0, 0, 1, C, 9, 7, F, E, 1, 6, E

and then

to assign the

specified hexadecimal value “001C97FE16EC”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

*B08FE*

BtMacAddr

B08FE

(Length: 12 digits; 0-F)

Summary of Contents for CM-520





























































































































































































































































































































































Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands

Anmax CM-520, User Manual

Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands