Anmax CM-520 User Manual Download Page 168

Page: 168 / 348

Enter 152 End

*/$%ENTR* *ZEND*

Setting up your Operation Modes

7-3-2-15.

Enable/Disable Barcode Verification

Scan the appropriate barcode to enable or disable barcode verification mechanism which

allows the decoder to decode the scanned data repetitively for better accuracy. By default,

when the feature is enabled, the device will verify the barcode one more time. To specify

the particular number of times for executing barcode verification, please refer to

Section

6-2-23

Chapter 6

to further configure

BarDblConfirmCnt

parameter.

7-3-2-16.

Set Type of Case Conversion

This parameter allows you to initiate letter case conversion which treats the decoded

message as a whole and converts it between upper case and lower case according to the

setting. Scan the appropriate the label to specify the type of case conversion.

*C0380*

None

C0380

*C0381*

Inverse

C0381

*C0382*

Lower

C0382

*C0383*

Upper

C0383

*C0210*

Disable

C0210

*C0211*

Enable

C0211

Summary of Contents for CM-520





























































































































































































































































































































































Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands

Anmax CM-520, User Manual

Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands