Anmax CM-520 User Manual Download Page 100

Page: 100 / 348

Enter 84 End

*/$%ENTR* *ZEND*

Editing General Settings

6-2-22.

Set Time-out Period for Configuration Mode

The timeout period mentioned here refers to the length of time the device is allowed to

remain idle ever since

ENTER

barcode is scanned to initiate Configuration mode. Once

the time-out session expires, the scanner will automatically exit Configuration mode. This

parameter allows you to configure the timeout limit which works best for you.

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

SetupTime

barcode to configure the length of the timeout session.

(3)

Please refer to Decimal/Hexadecimal Table in the appendix to scan decimal value

barcodes representing the desired decimal value in the range of 0 to 255. For

instance, to set timeout period to 1 second, then scan

to assign the specified

decimal value “1”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

6-2-23.

Set Time-out Period for Decoding Add-on Codes

This feature refers to the amount of time allocated to decode the extra add-on code for

UPC-A, UPC-E, EAN-13 and EAN-8 symbologies. Within the specified time frame, the

supplementary symbol will be decoded and then transmitted as part of the output data if

identified in the scanned barcode. To ensure the parameter functions normally, you have to

properly enable the add-on symbol in WPC barcodes at the same time to have it

recognizable during the decoding process.

*A5FE0*

SetupTime

A5FE0

(Length: 1 digit / Range: 0-255/ Unit: 1000ms)

Summary of Contents for CM-520





























































































































































































































































































































































Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands

Anmax CM-520, User Manual

Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands