Anmax CM-520 User Manual Download Page 124

Page: 124 / 348

Enter 108 End

*/$%ENTR* *ZEND*

Setting up your Operation Modes

7-2-1-20.

Set Transfer Count for Time Delay for HID

This parameter allows you to specify the number of digits which has to be transmitted to

initiate a time delay referring to an intentional deferment of data transmission. Please

follow the below steps to set the transfer count for time delay if the associated operations

are performed using USB HID interface.

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

StdHidTxCharGapCnt

barcode to configure the transfer count for time

delay for HID.

(3)

Please refer to Decimal/Hexadecimal Table in the appendix to scan decimal value

barcodes representing the desired value in the range of 0 to 255. For instance, to

initiate a timeout after 10 digits are transmitted, scan

first and then

to assign

the specified decimal value “10”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

*AB1C7*

AB1C7

*ABDE0*

StdHidTxCharGapCnt

ABDE0

(Length: 1 digit / Range: 0-255)

*AB1C8*

AB1C8

Summary of Contents for CM-520





























































































































































































































































































































































Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands

Anmax CM-520, User Manual

Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands