Anmax CM-520 User Manual Download Page 225

Page: 225 / 348

Enter 209 End

*/$%ENTR* *ZEND*

Configuring Symbology

8-3-6.

Truncate Leading Zeros

Scan

Enable

label to shrink the barcode message by getting rid of leading zeros.

8-3-7.

Remove Leading Characters

Truncate Lead

parameter allows you to specify the number of characters which you intend

to remove forwards from the start of UPC-E barcode. In doing so, you are able to format the

decoded message beforehand by taking out the necessary barcode parts and preserve the

desired segments for your benefit. Follow the below procedure to complete the

configuration.

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

TrunLead

barcode to specify the number of characters to delete forwards from

the start of the decoded data.

(3)

Please refer to Decimal/Hexadecimal table in the appendix to scan decimal value

barcodes representing the desired number in the range of 0 to 255. For instance, to

remove first three digits out of every UPC-E symbol, then scan

to assign the

specified decimal value “3”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

*D2060*

Disable

D2060

*D2061*

Enable

D2061

(Length: 1 digit / Range: 0-255)

*D34E0*

TrunLead

D34E0

Summary of Contents for CM-520





























































































































































































































































































































































Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands

Anmax CM-520, User Manual

Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands