Anmax CM-520 User Manual Download Page 95

Page: 95 / 348

Enter 79 End

*/$%ENTR* *ZEND*

Editing General Settings

6-2-12.

Enable/Disable Date and Time Info in the Header

Scan the appropriate barcode to determine whether or not to send out date information as

part of header information.

6-2-13.

Enable/Disable Record Count Info in the Header

Record count information refers to the total number of scanned barcodes. Read the

appropriate barcode to determine whether or not to send out the record count as part of

header information.

6-2-14.

Enable/Disable Footer

Footers refer to additional information which is appended to the decoded message while

saved barcodes are transmitted in Memory mode. Scan the appropriate barcode to

determine whether or not to send out the footer information as part of transmitted data.

*A4620*

Disable

A4620

*A4621*

Enable

A4621

*A4630*

Disable

A4630

*A4631*

Enable

A4631

*A4700*

Disable

A4700

*A4701*

Enable

A4701

Summary of Contents for CM-520





























































































































































































































































































































































Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands

Anmax CM-520, User Manual

Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands