Anmax CM-520 User Manual Download Page 125

Page: 125 / 348

Enter 109 End

*/$%ENTR* *ZEND*

Setting up your Operation Modes

7-2-1-21.

Set Time Delay for a Digit for HID

This parameter refers to the amount of elapsed time to delay transmitting a digit. Please

follow the below steps to set time delay for transmitting a digit if the associated

operations are performed using USB HID interface.

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

StdHidTxCharGapTime

barcode to configure delay time for a digit for

HID.

(3)

Please refer to Decimal/Hexadecimal Table in the appendix to scan decimal value

barcodes representing the desired value in the range of 0 to 255. For instance, to

defer transmitting a digit for 0.2 seconds, scan

2, 0

and then

to assign the

specified decimal value “200”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

*ABEE0*

StdHidTxCharGapTime

ABEE0

(Length: 1 digit / Range: 0-255/ Unit: 1ms)

Summary of Contents for CM-520





























































































































































































































































































































































Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands

Anmax CM-520, User Manual

Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands