Anmax CM-520 User Manual Download Page 103

Page: 103 / 348

Enter 87 End

*/$%ENTR* *ZEND*

Editing General Settings

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

Header

barcode to configure the length of the timeout session.

(3)

Please refer to ASCII Code Table and Decimal/Hexadecimal Table in the

appendix to scan hexadecimal value barcodes representing the desired string

which has to be at most 12 characters in length. For instance, to place the

employee name "Mark" in the header section, scan

4, D, 6, 1, 7, 2, 6

followed by

to assign the specified hexadecimal value “4D61726B”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

6-2-27.

Set Footer Information

Footer information refers to additional messages which are appended to data output while

the scanned barcodes are sent out in Memory mode. This special parameter allows you to

customize your own custom footer to add clarity of transmitted data.

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

Footer

barcode to configure the length of the timeout session.

(3)

Please refer to ASCII Code Table and Decimal/Hexadecimal Table in the appendix

to scan hexadecimal value barcodes representing the desired string which has to be

at most 12 characters in length. For instance, to place the employee name "Mark"

in the footer section, scan

4, D, 6, 1, 7, 2, 6

followed by

to assign the specified

hexadecimal value “4D61726B”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

*A60E6*

Footer

A60E6

(Length: 12 digits)

Summary of Contents for CM-520





























































































































































































































































































































































Search results

Summary of Contents for CM-520

Reviews:

Anmax CM-520, User Manual, Page: 103 / 348

Search results

Summary of Contents for CM-520

Reviews: