background image

 

                                                                   

             

Enter                                                                        95                                                      End 

*/$%ENTR*                            *ZEND* 

Setting up your Operation Modes 

 

7

 

 

 

 

 

7-2.

 

Cable Mode 

Please  be  advised  the  following  parameters  in  this  section  simply  work  for  the  associated 

operations  in  Cable  mode.  Make  sure  that  you  appropriately  conduct  the  operations  using 

Cable mode. 

7-2-1.

 

Output Interface Options 

In  terms  of  output  interface  options,  it  is  more  about  technical  configuration  regarding 

how  you  want  barcode  data  to  be  transmitted  between  devices  in  Cable  mode  before 

scanned  barcode  is  further  processed.  Properly  configure  your  scanner  according  to  the 

realistic situation will lead to satisfactory data transmission performance.   

7-2-1-1.

 

Set Data Transfer Rate for SPP 

Data  transfer  rate,  measured  in  bits  per  second,  refers  to  speed  of  digital  data  travelled 

among devices. Scan the appropriate barcode to specify  data transfer rate for SPP if the 

associated operations are performed using RS-232 or USB COM interfaces. 

 

 

 

 

       

7-2-1-2.

 

Set Length of Stop Bit for SPP 

Stop  bit  follows  after  the  end  of  data in  transit  as  to  signal  the  end  of  transmitted  data. 

Scan  the  appropriate  barcode  to  specify  the  length  of  stop  bit  for  SPP  if  the  associated 

operations are performed using RS-232 or USB COM interfaces. 

 

 

 

 

 

*AA020* 
 
 
 
 
 
 
 

7 Bits 

AA020 

 

 

*AA021* 
 
 
 
 
 
 

8 Bits 

AA021 

 

 

*AA030* 
 
 
 

1 Bit 

AA030 

 

 

*AA031* 
 
 

2 Bits 

AA031 

 

 

Summary of Contents for CM-520





























































































































































































































































































































































Reviews: