Anmax CM-520 User Manual Download Page 151

Page: 151 / 348

Enter 135 End

*/$%ENTR* *ZEND*

Setting up your Operation Modes

7-3.

Memory Mode

Please be advised the following parameters in this section simply works for the associated

operations in Memory mode. Make sure that you appropriately conduct the operations using

Memory mode.

7-3-1.

Scanner Options

A selection of scanner options, from setting button functions to adjusting the buzzer

volume and vibrator, is offered to personalize the device to suit your usage habits.

7-3-1-1.

Set Scan Mode

Scan Mode refers to how the scanner reacts to the scanned barcode. By default, Scan

Mode is set to be

Momentary

. In this case, LED light will stay on as long as Scan button

is pressed down, and automatically turn off once Scan Button is released or a barcode is

scanned. However, with

Good Read Off

settings, LED will remain lit for a specified

period of time with a release of the pressed Scan Button, and afterwards dim only when

the barcode is successfully decoded or the timeout period expires. In

Continue

Scan

Mode, the device will continuously send out light till the cable is unplugged, after Scan

Button is pressed down and then released. Scan

Toogle

label if you intend to gain more

flexibility in when to read a barcode. A press on Scan Button will lead in switching on the

light whereas either a successful decoding of a barcode or giving it another press

correspondingly switches off the light. Please scan the appropriate label to determine your

preferred scan mode.

*BE080*

GoodReadOff

BE080

*BE081*

Momentary

BE081

*BE082*

Continue

BE082

*BE083*

Toogle

BE083

Summary of Contents for CM-520





























































































































































































































































































































































Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands

Anmax CM-520, User Manual

Search results

Summary of Contents for CM-520

Reviews:

Related manuals for CM-520

Brands by name

Popular brands