AGFA DRYSTAR AXYS Service Manual Download Page 244

Page: 244 / 461

DD+DIS033.07E

Repair and Service

Electrical and Mechanical Codes, Fuses, LEDs

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Edition 1, Revision 0

DRYSTAR AXYS

Chapter 3.4 / 6

10-2007 Type

5367/100

Agfa Company Confidential

Jumper C4

Setting

Function

1-2

open

ID Bit 3

3-4

open

ID Bit 2

5-6

open

ID Bit 1

7-8

open

ID Bit 0

9-10

open

Not used

11-12

open

Write Protect

Table 4

2 Fuses

The printer has no fuses that can be replaced.

If one of the fuses in the power supply is defective, the whole Power supply unit must
be replaced - refer to section 3.5.

3 LEDs

The following tables show the status of the LED indications and the corresponding
function:

LED's on...

Refer to

DEVIL Board

THANOS Board

Power supply

Front Panel

Rear Panel

Summary of Contents for DRYSTAR AXYS














































































































































































































































































































































































































































































Search results

Summary of Contents for DRYSTAR AXYS

Reviews:

Brands by name

Popular brands

AGFA DRYSTAR AXYS, Service Manual

Search results

Summary of Contents for DRYSTAR AXYS

Reviews:

Brands by name

Popular brands