manualshive.com logo in svg

AGFA DRYSTAR AXYS, Service Manual

Share
Download
AGFA DRYSTAR AXYS Service Manual Download Page 44

 
 
DD+DIS033.07E 

Controls, Connections and Setup Procedure

 
 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled. 

Edition 1, Revision 1 

DRYSTAR AXYS 

Chapter 1 / 8 

06-2008 Type 

5367/100 

Agfa Company Confidential

 

 

3 

Adapting the Printer Settings 

 

The purpose of this section is to list the additional, optional settings of the printer that 
are not covered by the Printer Installation Wizard. 

The following table lists these settings. 

 

Printer Setting 

Importance

Accessible via ... 

Details see...

Default film calibration 

optional 

Key-operator and Service menu 

3.1

 

Default densitometer 

optional 

Key-operator and Service menu 

3.2

 

Film view 

optional 

Key-operator and Service menu 

3.3

 

Beep on empty tray 

optional 

Key-operator and Service menu 

3.4

 

RF Tag 

optional 

Service menu  

(Browser only) 

3.5

 

Mammo license 

optional 

Service menu 

(Browser only) 

3.6

 

Site data* 

mandatory**

Service menu 

X3.7

3.7

 

* if created offline via the "Site Data Tool", it is possible to enter the site data via the printer  
  installation wizard. 

** only mandatory if not yet done during the printer installation wizard. As long as the site specific data  
   are not entered the user will be remineded after each boot-up of the printer. 

 

The example screens for configuration user interfaces are further on 

browser user 

interface

 related. The path to access the screens is the same for local keypad and 

browser.  

 

Summary of Contents for DRYSTAR AXYS














































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands