manualshive.com logo in svg

AGFA DRYSTAR AXYS, Service Manual

Share
Download
AGFA DRYSTAR AXYS Service Manual Download Page 247

 
 
DD+DIS033.07E 

Repair and Service

Electrical and Mechanical Codes, Fuses, LEDs

 
 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled. 

3.3 

Power Supply 

 

536634ab.cdr

 

Figure 3 

 

LED 

Status 

Color 

Function 

Overtemp 

On 

 
 

Off 

Red 

Temperature inside power supply  
exceeded permissible limits. Operation not 
possible*. 
Temperature inside power supply  
within permissible limit.  

+ 3.3 V 

On 

Off 

Green 

+3.3 V present 

+3.3 V not present 

+ 5 V 

On 

Off 

Green 

+5 V present 

+5 V not present 

+12 V 

On 

Off 

Green 

+12 V present 

+12 V not present 

-12 V 

On 

Off 

Green 

-12 V present 

-12 V not present 

+24 V 

On 

Off 

Green 

+24 V present 

+24 V not present 

13..27 V 

On 

Off 

Green 

voltage between 13 V and 27 V 

voltage < 13 V 

*When the temperature inside the power supply exceeds the permissible limit, printing 
can continue for up to 120 seconds. After this delay the power supply switches off the 
power and checks the temperature every 20 seconds. As soon as the temperature is 
below the permissible limit, it switches on again. 

 

Edition 1, Revision 0 

DRYSTAR AXYS 

Chapter 3.4 / 9 

10-2007 Type 

5367/100 

Agfa Company Confidential

 

Summary of Contents for DRYSTAR AXYS














































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands