manualshive.com logo in svg

ABB OmniCore IRB 6740, Product Manual, Page: 448 / 664

Share
Download
ABB OmniCore IRB 6740 Product Manual Download Page 448

Note

Action

Follow the instructions given in the refer-
ence calibration routine on the FlexPendant
to create reference values.

If the robot is to be calibrated with refer-
ence calibration:

Find previous reference values for the axis
or create new reference values. These val-
ues are to be used after the repair proced-
ure is completed, for calibration of the ro-
bot.

Creating new values requires possibility to
move the robot.
Read more about reference calibration for
Axis Calibration in

Reference calibration

routine on page 619

.

If no previous reference values exist, and
no new reference values can be created,
then reference calibration is not possible.

If the robot is to be calibrated with fine
calibration:

Remove all external cable packages
(DressPack) and tools from the robot.

Removing the gearbox

These procedures describe how to remove the gearbox.

Removing tools and equipment from the turning disc

Note

Action

This is done to achieve the best
stability of the complete arm sys-
tem, when it is resting by itself after
removal.

Remove tools and other equipment fitted on the
turning disc.

1

Removing the covers for Foundry Plus and floor mounted robots

Note

Action

xx2200001430

Protection type Foundry Plus

Remove the axis-1 cable protection plates by
removing the attachment screws.

1

Continues on next page

448

Product manual - IRB 6740

3HAC085701-001 Revision: A

© Copyright 2023 ABB. All rights reserved.

5 Repair

5.9.1 Replacing the axis-1 gearbox

Continued

Summary of Contents for OmniCore IRB 6740

























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments