ABB IRB 660 Product Manual Download Page 194

Page: 194 / 362

Note

Action

If the robot is to be calibrated with fine
calibration:

Remove all external cable packages
(DressPack) and tools from the robot.

Removal, upper arm

The procedure below details how to remove the upper arm.

Note

Action

Decide which calibration routine to use, and
take actions accordingly prior to beginning
the repair procedure.

Remove all equipment fitted to the turning
disk.

Move the upper arm to a horizontal position.

DANGER

Turn off all:

•

electric power supply

•

hydraulic pressure supply

•

air pressure supply

to the robot, before entering the robot
working area.

Secure the

upper arm

with roundslings in

an overhead crane.

Detailed in section

Remove the

cable harness

in the upper arm.

CAUTION

The complete upper arm with weighs 170
kg (without any additional equipment fitted).
Use a suitable lifting accessory to avoid in-
jury to personnel!

Raise the lifting equipment to take the
weight of the upper arm.

Detailed in section

Replacing the balan-

cing device on page 236

Remove the

balancing device

Detailed in section

Replacement of linkage

- upper rod on page 201

Remove the

linkage

Detailed in section

Replacing the linkage

- lower rod on page 205

Detailed in section

Replacement of linkage

- link on page 209

Detailed in section

Replacing the parallel

rod on page 216

Remove the

parallel rod.

Continues on next page

194

Product manual - IRB 660

3HAC025755-001 Revision: W

4 Repair

4.4.3 Replacement of upper arm

Continued

Summary of Contents for IRB 660











































































































































































































































































































































































Search results

Summary of Contents for IRB 660

Reviews:

ABB IRB 660, Product Manual, Page: 194 / 362

Search results

Summary of Contents for IRB 660

Reviews: