
19
S1-08
REV Run Brake
Release Torque
(Rev Release T)
0~
200
1%
0
N
N
N
A
A
687H
FWD Run Torque
Forcing Value
(Fwd Torq
Forcing)
0~
200
S1-09
FWD Run Torque
Compensation
Value
(Fwd T-COMP
Value)
-200~
200
1%
50
*
*Factory/default settings will vary
based on Control Mode (refer to
attached table).
The lower frame is displayed when
operating in Flux Vector Mode.
N
N
N
A
A
688H
Rev Run Torque
Forcing Value
(Rev Torq
Forcing)
-200~
0
S1-10
REV Run Torqu
Compensation
Value
(Rev T-COMP
Value)
-200~
200
1%
0
The lower frame is displayed when
operating in Flux Vector Mode.
N
N
N
A
A
689H
Torque Forcing
Delay Time
(Trq Frcing Flter)
S1-11
Torque
Compensation
Delay Time
(T-COMP Filter)
0~
200
1ms
50
The lower frame is displayed when
operating in Flux Vector Mode.
N
N
N
A
A
68AH
S1-12
FWD Run Brake
Hold Frequency
(Fed Hold F)
0.0~
20.0
0.1Hz
3.0
Note-6
N
A
A
A
A
68BH
S1-13
REV Run Brake
Hold Frequency
(Rev Hold F)
0.0~
20.0
0.1Hz
3.0
Note-6
N
A
A
A
A
68CH
S1-14
Slipping
Prevention
Frequency
(Slip Prevent F)
0.0~
20.0
0.1Hz
3.0
*
*Factory/default settings will vary
based on Control Mode (refer to
attached table).
N
A
A
A
A
68DH
S1-15
Slipping
Prevention Time
(Slip Prevent T)
0.00~
10.00
0.01
sec
0.30
*
*Factory/default settings will vary
based on Control Mode (refer to
attached table).
N
A
A
A
A
68EH
S1-16
Sequence Fault
SE1 Detection
Time
(SE1 Det Time)
0.00~
2.00
0.01
sec
0.30
N
A
A
A
A
68FH
S1-17
Sequence Fault
SE2 Detection
Time
(SE2 Det TIme)
0.00~
2.00
0.01
sec
1.00
N
A
A
A
A
690H
S1-18
Sequence Fault
SE3 Detection
Time
(SE3 Det Time)
0.00~
2.00
0.01
sec
0.50
N
A
A
A
A
691H
S1-19
Sequence Fault
SE4 Detection
Time
(SE4 Det Time)
0.00~
2.00
0.01
sec
0.50
N
A
A
A
A
692H
S1-20
Operation in
Reverse
(Action @
Reverse)
0,1
1
0
0: Normal Motoring Operations
1: Regen Operation in Reverse
N
N
N
A
N
693H
S2-01
FWD Run
Command Min.
ON Time
(Fwd Min ON
Time)
0.00~
10.00
0.01
sec
0.00
N
A
A
A
A
694H
S2-02
REV Run
Command Min.
ON Time
(Rev Min ON
Time)
0.00~
10.00
0.01
sec
0.00
N
A
A
A
A
695H
Run CommandTuning
S2-03
Run Cmd Delay
Timer
(REV? FWD)
0.00~
10.00
0.01
sec
0.00
Enabled only with Motor 1.
N
A
A
A
N
696H
S3-01
Impact Stop Clip
Frequency
(Creep F At Stop)
0.0~
20.0
0.1Hz
3.0
*
*Factory/default settings will vary
based on Control Mode (refer to
attached table).
N
A
A
A
A
697H
Impact Stop
S3-02
Impact Stop Clip
Time
(Creep TIme @
Stop)
0.0~
20.0
0.1sec
10.0
N
A
A
A
A
698H
Note-6: If the frequency reference is reduced just below S4 -01, -02, -12, or -13 with no Stop Command entered (both FWD and
REV commands are closed), then the drive
will continue to run, using the forward frequency reference of either S4 -01 or
S4-12, whichever is larger. The reverse frequency command will be either S4 -02 or S4 -13, whichever of the two is larger.
*Not reset when the drive is initialized. Factory/default settings will vary based on drive capacity.
Содержание CIMR-F7Z
Страница 3: ......