YASKAWA CIMR-F7Z, Инструкция по эксплуатации

Страница: 10 / 67

7
b2-08
Magnetic Flux
Compensation Volume
(Field Comp)
0~
1000
1% 0
Sets the magnetic flux compensation
as a percentage of the no-load current
value (E2-03).
N N N A N 190H
b7-01
Droop Control gain
(Droop Quantity) 0.0~
100.0
0.1% 0.0 Y N N A A 1CAH
Droop Control
b7-02
Droop Control Delay
Time
(Droop Delay Time)
0.03~
2.00
0.01
sec
0.05 Y N N A A 1CBH
Note-1: Not reset when the drive is initialized (models in Japan are set to A1-00 = 1, while A1-02 = 22 concerns the Parameter Access
Level).
Note-2: Q: Quick-Start menu shows the parameters.
A: Advanced program menu shows the parameters.
N: Settings or changes are not possible.
Table 4.2.2 Parameter Table (2
)
Parameter Access Level
Note-2
Function
No.
Parameter Name
(Digital Operator
Display)
Setting
Range
Setting
Units
Factory
Settings
Comments
Chan
ges
on
the
Fly V/f
V/f
w/P
G
OLV CLV
Memo
bus Address
b9-01
Zero Servo Gain
(Zero Servo Gain)
0~100 1 5 N N N N A 1DAH
Zero Servo
b9-02
Zero Servo
Completion Width
(Zero Servo Count)
0~
16383
1 10 N N N N A 1DBH
C1-01
Acceleratio n Time 1
(Accel Time 1)
Y Q Q Q Q 200H
C1-02
Deceleration Time 1
(Decel Time 1)
Y Q Q Q Q 201H
C1-03
Acceleration Time 2
(Accel Time 2)
Y A A A A 202H
C1-04
Deceleration Time 2
(Decel TIme 2)
Y A A A A 203H
C1-05
Acceleration Time 3
(Accel Time 3)
N A A A A 204H
C1-06
Deceleration Time 3
(Decel Time 3)
N A A A A 205H
C1-07
Acceleration Time 4
(Accel TIme 4)
N A A A A 206H
C1-08
Deceleration Time 4
(Decel Time 4)
N A A A A 207H
C1-09
Emergency Stop
Time
(Fast Stop Time)
0.0~
6000.0
*
0.1
sec
10.0
Sets the time to accelerate from zero
to maximum frequency when
selected via a Multi-Function Input.
*The acceleration/deceleration
setting range will vary based on the
units selected in C1 -10. If C1-10 is
set to zero, then the setting range for
the Accel/decel time will be 0.00 to
600.00sec.
N A A A A 208H
C1-10
Accel/Decel Time
Setting Units
(Acc/Dec Units)
0, 1 1 1
0: Units of 0.01sec.
1: Units of 0.1sec.
N A A A A 209H
Acceleration / Deceleration Time
C1-11
Accel/Decel Time
Switching Frequency
(Acc/Dec SW Freq)
0.0~
400.0
0.1
Hz
0.0 N A A A A 20AH
C2-01
S-Curve
Characteristic Time
at Acceleration Start
(SCrv Acc@ Start)
0.00~
2.50
0.01
sec
0.20 N A A A A 20BH
C2-02
S-Curve
Characteristic Time
at Acceleration End
(SCrv Acc @ End)
0.00~
2.50
0.01
sec
0.20 N A A A A 20CH
C2-03
S-Curve
Characteristic Time
at Deceleration Start
(SCrv Dec @ Start)
0.00~
2.50
0.01
sec
0.20 N A A A A 20DH
S
-Curve Characteristics
C2-04
S-Curve
Characteristic Time
at Deceleration End
(SCrv Dec @ End)
0.00~
2.50
0.01
sec
0.00 N A A A A 20EH
C3-01
Slip Compensation
Gain
(Slip Comp Gain)
0.0~
2.5
0.1
1.0
*
*Factory/default settings will vary
based on Control Mode (refer to
attached table).
Y A N A A 20FH
C3-02
Slip Compensation
Primary Delay Time
(Sllip Comp Time)
0~
10000
1
ms
200
*
*Factory/default settings will vary
based on Control Mode (refer to
attached table).
N A N A N 210H
C3-03
Slip Compensation
Limit
(Slip Comp Limit)
0~
250
1% 200 N A N A N 211H
Slip Compensation
C3-04
Slip Compensation
Selection During
Regeneration
(Slip Comp Regen)
0,1 1 0
Determines whether slip
compensation is enabled or disabled
during regeneration.
0: Disabled 1: Enabled
N A N A N 212H