Yamaha R1 Series 2015 Скачать руководство пользователя страница 467

Страница: 467 / 704

THROTTLE BODIES

7-14

bodies.
Refer to “SYNCHRONIZING THE THROT-
TLE BODIES” on page 3-9.

EAS31160

REPLACING THE THROTTLE BODIES

1. Remove the throttle bodies from the vehicle.
2. Install a new throttle bodies to the vehicle.
3. Reset:

•

ISC (Idle Speed Control) learning values
Use the diagnostic code number “67”.
Refer to “SELF-DIAGNOSTIC FUNCTION
AND DIAGNOSTIC CODE TABLE (ECU)” on
page 9-5.

4. Adjust:

•

Throttle bodies synchronizing
Refer to “SYNCHRONIZING THE THROT-
TLE BODIES” on page 3-9.

5. Place the vehicle on a suitable stand so that

the rear wheel is elevated.

6. Check:

•

Engine idling speed
Start the engine, warm it up, and then mea-
sure the engine idling speed.

EAS31669

INSTALLING THE PRIMARY INJECTORS

NOTICE

ECA21550

• Always use new O-rings.

• When installing the injectors, do not allow

any foreign material to enter or adhere to

the injectors, fuel rails, or O-rings.

• Be careful not to twist or pinch the O-rings

when installing the injectors.

• When installing the injector, install it at the

same position as the removed cylinder.

• If an injector is subject to strong shocks or

excessive force, replace it.

• If installing the original fuel rail and bolts,

remove the white paint marks using a

cleaning solvent. Otherwise, paint chips on

the bolt seats could prevent the bolts from

being tightened to the specified torque.

1. Install a new seal onto the end of each injec-

tor.

2. Install the injectors “1” to the fuel rails “2”.
3. Install the primary injector joint “3”, making

sure to install them in the correct direction.

4. Install the injector assemblies to the throttle

bodies.

5. Check the injector pressure after the injectors

are installed.
Refer to “CHECKING THE INJECTOR
PRESSURE” on page 7-14.

EAS30481

CHECKING THE INJECTOR PRESSURE

TIP

•

After installing the injectors, perform the follow-
ing steps to check the injector pressure.

•

Do not allow any foreign materials to enter the
fuel lines.

1. Check:

•

Injector pressure

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the fuel injector pressure adapter “1”

to the injector joint “2”, and then connect an
air compressor “3” to the adapter.

b. Connect the pressure gauge “4” to the fuel in-

jector pressure adapter “1”.

Engine idling speed

1200–1400 r/min

Fuel rail screw (throttle body)

3.5 Nm (0.35 m·kgf, 2.5 ft·lbf)

Pressure gauge

90890-03153

Pressure gauge

YU-03153

Fuel injector pressure adapter

90890-03210

Fuel injector pressure adapter

YU-03210

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды