Yamaha R1 Series 2015 Скачать руководство пользователя страница 408

Страница: 408 / 704

CRANKCASE

5-67

EAS30389

DISASSEMBLING THE CRANKCASE

1. Place the engine upside down.
2. Remove:

•

Crankcase bolt (

40)

TIP

•

Loosen each bolt 1/4 of a turn at a time, in stag-
es and in a crisscross pattern. After all of the
bolts are fully loosened, remove them.

•

Loosen the bolts in the proper sequence as
shown.

•

The numbers embossed on the crankcase in-
dicate the crankcase tightening sequence.

3. Remove:

•

Lower crankcase

NOTICE

ECA13900

Tap on one side of the crankcase with a soft-

face hammer. Tap only on reinforced por-

tions of the crankcase, not on the crankcase

mating surfaces. Work slowly and carefully

and make sure the crankcase halves sepa-

rate evenly.

4. Remove:

•

Dowel pins

5. Remove:

•

Crankshaft journal lower bearing

•

Balancer shaft journal bearing
(from the lower crankcase)

TIP

Identify the position of each part very carefully so
that it can be reinstalled in its original place.

EAS30390

CHECKING THE CRANKCASE

1. Thoroughly wash the crankcase halves in a

mild solvent.

2. Thoroughly clean all the gasket surfaces and

crankcase mating surfaces.

3. Check:

•

Crankcase
Cracks/damage

Replace.

•

Oil delivery passages
Obstruction

Blow out with compressed air.

EAS30397

ASSEMBLING THE CRANKCASE

1. Lubricate:

•

Crankshaft journal bearing inner surface
(with the recommended lubricant)

2. Apply:

•

Sealant
(onto the crankcase mating surfaces)

TIP

Do not allow any sealant to come into contact
with the oil gallery or crankshaft journal bear-
ings, or balancer shaft journal bearings.

3. Install:

•

Dowel pins

Recommended lubricant

Engine oil

Yamaha bond No. 1215

90890-85505

(Three bond No.1215®)

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды