Yamaha R1 Series 2015 Скачать руководство пользователя страница 206

Страница: 206 / 704

PERIODIC MAINTENANCE

3-32

7. Measure:

•

Engine oil pressure
(at the following conditions)

Out of specification

Check.

8. Remove:

•

Oil pressure gauge

•

Adapter C

•

Oil pressure switch joint bolt

•

Oil pressure switch joint (with the O-ring)

9. Install:

•

O-ring “1”

•

Oil pressure switch joint (with the oil pressure
switch) “2”

•

Oil pressure switch joint bolt “3”

EAS30811

CHECKING THE COOLANT LEVEL

1. Stand the vehicle on a level surface.

TIP

•

Place the vehicle on a suitable stand.

•

Make sure the vehicle is upright.

2. Check:

•

Coolant level
The coolant level should be between the
maximum level mark “a” and minimum level
mark “b”.
Below the minimum level mark

Add the

recommended coolant to the proper level.

NOTICE

ECA21281

• Adding water instead of coolant dilutes the

antifreeze concentration of the coolant. If

water is used instead of coolant; check,

and if necessary, correct the antifreeze

concentration of the coolant.

• Use only distilled water. However, if dis-

tilled water is not available, soft water may

be used.

3. Start the engine, warm it up for several min-

utes, and then turn it off.

4. Check:

•

Coolant level

TIP

Before checking the coolant level, wait a few
minutes until it settles.

EAS30812

CHECKING THE COOLING SYSTEM

1. Check:

•

Radiator “1”

•

Radiator inlet hose “2”

•

Radiator outlet hose “3”

•

Water pump inlet pipe “4”

•

Water pump outlet pipe “5”

•

Oil cooler “6”

•

Oil cooler outlet hose “7”

•

Oil cooler inlet hose “8”

Oil pressure

220.0 kPa/5000 r/min@80

(31.9 psi/5000 r/min@176

Engine oil pressure

Possible causes

Below specification

•

Faulty oil pump

•

Clogged oil filter

•

Leaking oil passage

•

Broken or damaged

oil seal

Above specification

•

Faulty oil filter

•

Oil viscosity too high

Oil pressure switch joint bolt

10 Nm (1.0 m·kgf, 7.2 ft·lbf)

New

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды