Yamaha R1 Series 2015 Скачать руководство пользователя страница 184

Страница: 184 / 704

PERIODIC MAINTENANCE

3-10

5. Install:

•

Air filter case
Refer to “AIR FILTER CASE” on page 7-4.

•

Fuel tank
Refer to “FUEL TANK” on page 7-1.

6. Check:

•

Throttle body synchronization

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Start the engine, warm it up for several min-

utes, and then let it run at the specified en-
gine idling speed.

b. Check the vacuum pressure.

If out of specification

Adjust the throttle

body synchronization.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

Adjusting the throttle body synchronization

1. Adjust:

•

Throttle body synchronization

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Start the engine, warm it up for several min-

utes, and then let it run at the specified en-
gine idling speed.

b. Using the throttle body that has the bypass air

screw “1” with a white paint mark as the stan-
dard, adjust the other throttle bodies by turn-
ing its bypass air screw in or out.

NOTICE

ECA21300

Do not turn the bypass air screw (white paint

mark) of the throttle body that is the stan-

dard. Otherwise, the engine may run roughly

at idle and the throttle bodies may not oper-

ate properly.

TIP

•

Turn the bypass air screw using the carburetor
angle driver.

•

After each step, rev the engine two or three
times, each time for less than a second, and
check the synchronization again.

•

If a bypass air screw was removed, turn the
screw in fully and be sure to synchronize the
throttle bodies.

•

If the throttle body synchronization can not be
adjusted using the bypass air screw, clean or
replace the throttle bodies.

•

The difference in vacuum pressure between
the throttle bodies should not exceed 1.33 kPa
(10 mmHg).

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

2. Stop the engine and remove the measuring

equipment.

3. Install:

•

Caps

4. Install:

•

Air filter case
Refer to “AIR FILTER CASE” on page 7-4.

•

Fuel tank
Refer to “FUEL TANK” on page 7-1.

•

Fuel tank cover
Refer to “GENERAL CHASSIS (2)” on page
4-7.

•

Rider seat
Refer to “GENERAL CHASSIS (1)” on page
4-1.

5. Adjust:

•

Throttle grip free play
Refer to “CHECKING THE THROTTLE
GRIP” on page 3-36.

Engine idling speed

1200–1400 r/min

The difference in vacuum pres-

sure between the throttle bodies

should not exceed 1.33 kPa (10

mmHg).

Engine idling speed

1200–1400 r/min

Carburetor angle driver 2

90890-03173

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды