Yamaha R1 Series 2015 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 704

background image

FEATURES

1-41

“Logging” (for CCU-equipped models)

Vehicle and riding information can be recorded
(logged) and this data can be accessed with a
smart device. (Refer to “CONNECTING TO THE
CCU (for YZF-R1M)” on page 4-5.)

[To start and stop logging]

1. From the MENU screen, select “Logging”.

TIP

If a CCU is not installed or the CCU is not prop-
erly connected, then the “Logging” module can-
not be selected.

2. Select START to start logging.

3. To stop the “Logging” function, select STOP

or turn the vehicle off.

“Maintenance”

This function allows you to record distance trav-
eled between engine oil changes (use the OIL
item), and for two other items of your choice (use
INTERVAL 1 and INTERVAL 2).

[To reset a maintenance item]

1. From the MENU screen, select “Mainte-

nance”.

2. Select the item you want to reset.

3. Long push the wheel switch to reset the item.

TIP

Maintenance item names cannot be changed.

“Unit”

This module allows you to set the fuel consump-
tion  units,  and  for  certain  markets,  the  display
can be switched between kilometers and miles.
When  using  kilometers,  the  fuel  consumption
units  can  be  changed  between  km/L  or
L/100km. When using miles, MPG will be avail-
able.

[To set the distance or fuel consumption

units]

1. From the MENU screen, select “Unit”.

1. Logging indicator

GPS

GPS

1

GPS

INTERVAL 2

OIL
INTERVAL 1

000000 km

123456 km
123456 km

Maintenance

km/h

GPS

12:00

«
...
48
49
50
51
52
...
»

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R1 Series 2015

Бренд: National Cycle Страницы: 3

Бренд: DAELIM Страницы: 68

Stealth Air Cleaner Kit

Бренд: S&S Cycle Страницы: 4

Бренд: Ducati Страницы: 77

Бренд: BOXER Страницы: 11

Бренд: hepco & becker Страницы: 4

Бренд: Honda Страницы: 127

Бренд: Thunderbike Страницы: 7

MOTO NOSTRA MN4602

Бренд: SC Страницы: 8

TRACER MTT9K 2019

Бренд: Yamaha Страницы: 122

TT-R125(N) 2000

Бренд: Yamaha Страницы: 508

TT-R125(R) 2002

Бренд: Yamaha Страницы: 510

Бренд: Yamaha Страницы: 610

TT-R125(S) 2003

Бренд: Yamaha Страницы: 610

Бренд: Yamaha Страницы: 616

Бренд: Yamaha Страницы: 90

Бренд: X&I Страницы: 59

Бренд: Honeywell Страницы: 93

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды