Yamaha R1 Series 2015 Скачать руководство пользователя страница 193

Страница: 193 / 704

PERIODIC MAINTENANCE

3-19

WARNING

EWA13210

New tires have a relatively low grip on the

road surface until they have been slightly

worn. Therefore, approximately 100 km

should be traveled at normal speed before

any high-speed riding is done.

TIP

For tires with a direction of rotation mark “1”:

•

Install the tire with the mark pointing in the di-
rection of wheel rotation.

•

Align the mark “2” with the valve installation
point.

EAS30641

CHECKING THE WHEEL BEARINGS

The following procedure applies to all of the
wheel bearings.
1. Check:

•

Wheel bearings
Refer to “CHECKING THE FRONT WHEEL”
on page 4-27 and “CHECKING THE REAR
WHEEL” on page 4-38.

EAS30802

CHECKING THE SWINGARM OPERATION

1. Check:

•

Swingarm operation
Swingarm not working properly

Check the

swingarm.
Refer to “SWINGARM” on page 4-112.

2. Check:

•

Swingarm excessive play
Refer to “SWINGARM” on page 4-112.

EAS30643

LUBRICATING THE SWINGARM PIVOT

1. Lubricate:

•

Oil seals

•

Collars

Refer to “INSTALLING THE SWINGARM” on
page 4-114.

EAS30644

ADJUSTING THE DRIVE CHAIN SLACK

NOTICE

ECA13550

A drive chain that is too tight will overload

the engine and other vital parts, and one that

is too loose can skip and damage the swing-

arm or cause an accident. Therefore, keep

the drive chain slack within the specified lim-

its.

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

TIP

Place the vehicle on a suitable stand so that the
rear wheel is elevated.

2. Shift the transmission into the neutral posi-

tion.

3. Check:

•

Drive chain slack “a”
Out of specification

Adjust.

Rear tire

Size

YZF-R1 190/55 ZR17M/C (75W)

YZF-R1M 200/55 ZR17M/C (78W)

Manufacturer/model

YZF-R1

BRIDGESTONE/BATTLAX RAC-

ING STREET RS10R G or PIREL-

LI/DIABLO SUPERCORSA SP

YZF-R1M

BRIDGESTONE/BATTLAX RAC-

ING STREET RS10R G

Recommended lubricant

Lithium-soap-based grease

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды