Yamaha R1 Series 2015 Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 704

Yamaha R1 Series 2015 Скачать руководство пользователя страница 141

CABLE ROUTING

2-66

1. Horn lead
2. Main switch lead
3. Left handlebar switch lead
4. Throttle cable (accelerator cable)
5. Throttle cable (decelerator cable)
6. Right handlebar switch lead
7. Cylinder identification sensor lead
8. Front wheel sensor lead
9. Ignition coil #4 coupler
10.Ignition coil #3 coupler
11.Accelerator position sensor coupler
12.Atmospheric pressure sensor coupler
13.Throttle servo motor coupler
14.Immobilizer unit coupler
15.Ignition coil #2 coupler
16.Intake air pressure sensor coupler
17.Air induction system solenoid lead
18.Ignition coil #1 coupler
19.Intake funnel servo motor lead
20.Plastic locking tie
21.Immobilizer unit lead
22.Sub-wire harness (for YZF-R1M)
23.Guide
24.Radiator bracket
25.Radiator fan motor lead
26.Intake solenoid vacuum hose
27.Atmospheric pressure sensor
28.Immobilizer unit lead (wire harness)
29.Wire harness

A. Fasten the horn lead at the positioning tape

with the lower bracket cover clamp as shown

in the illustration. Route the excess portion of

the horn lead (between the positioning tapes)

to the outside of the rib on the lower bracket

cover.

B. Insert the wire harness clamp into the hole in

the frame.

C. To intake funnel servo motor
D. Fasten the intake solenoid vacuum hose with

the plastic locking tie using the front position

of the quick fastener as a guide. Make sure

that the end of the plastic locking tie does not

protrude above the intake solenoid vacuum

hose.

E. When connecting the intake solenoid vacuum

hose, may apply lubrication (water, soapy

water, silicone fluid, or ethanol) to the hose.

F. Fasten the intake solenoid vacuum hose with

the plastic locking tie using the rear position

of the wire harness clamp as a guide. Make

sure that the end of the plastic locking tie

does not protrude above the intake solenoid

vacuum hose.

G. To horn

H. Fasten the leads (right handlebar switch lead

(blue), left handlebar switch lead (gray), main

switch lead (white), sub-wire harness (for

YZF-R1M) (white)) at the positioning tape on

the guide with the plastic locking tie. Cut off

the excess end of the tie to 5 mm (0.2 in) or

less.

I. To front wheel sensor
J. Fasten the front wheel sensor lead to the end

of the R section of the brake pipe with the

plastic locking tie as shown in the illustration.

Cut off the excess end of the plastic locking

tie to 5 mm (0.2 in) or less. The buckle of the

plastic locking tie may be facing in any direc-

tion.

K. Route the wheel sensor lead through the

claw of the bracket.

L. Connect the immobilizer unit coupler, and

then install it to the stay.

M. Fasten the immobilizer unit lead and wire har-

ness with the plastic locking tie. Align the

plastic locking tie with the white tape. Point

the end of the plastic locking tie forward. Do

not cut off the excess end of the plastic lock-

ing tie.

N. Fasten the wire harness to the guide with the

plastic locking tie. The buckle of the plastic

locking tie may be facing in any direction. Cut

off the excess end of the tie to 5 mm (0.2 in)

or less.

O. Fasten the intake solenoid vacuum hose onto

the wire harness with the plastic locking tie.

Face the buckle of the plastic locking tie out-

ward. (2 locations)

P. Insert the wire harness clamp until it contacts

the claw of the electrical components tray.

Q. Fasten the front wheel sensor lead at the

positioning tape with the clamp as shown in

the illustration.

«
...
139
140
141
142
143
...
»

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов