Yamaha R1 Series 2015 Скачать руководство пользователя страница 460

Страница: 460 / 704

AIR FILTER CASE

7-7

NOTICE

ECA17550

• Make sure that the intake funnel smoothly

moves to the contacting surface between

upper stopper and lower seating position

when it is moved by hand.

• Make sure that the intake funnel smoothly

strokes from the upper position to the seat-

ing position by its own weight.

EAS31665

INSTALLING THE INTAKE FUNNEL AND AIR

FILTER CASE

1. Install:

•

Intake funnel servo motor

•

Intake funnel servo motor rod assembly

•

Air filter case

•

Intake funnel assembly

•

Intake funnel assembly bolt

EAS30465

CHECKING THE INTAKE FUNNEL

OPERATION

1. Check:

•

Intake funnel servo motor operation

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Activate the diagnostic mode and select the

diagnostic code number “34”.
Refer to “SELF-DIAGNOSTIC FUNCTION
AND DIAGNOSTIC CODE TABLE (ECU)” on
page 9-5.

b. Set the start/engine stop switch to “ ”.
c. Check that the stopper lever “a” contacts the

lever “b” (figure “A”).

d. Check that the intake funnel seal mates with

the fixed intake funnel (figure “B”).

TIP

The intake funnels should move smoothly and

should not make any unusual sound.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS30466

INSTALLING THE SECONDARY INJECTORS

NOTICE

ECA21550

• Always use new O-rings.

• When installing the injectors, do not allow

any foreign material to enter or adhere to

the injectors, fuel rails, or O-rings.

• Be careful not to twist or pinch the O-rings

when installing the injectors.

• When installing the injector, install it at the

same position as the removed cylinder.

• If an injector is subject to strong shocks or

excessive force, replace it.

• If installing the original fuel rail and bolts,

remove the white paint marks using a

cleaning solvent. Otherwise, paint chips on

the bolt seats could prevent the bolts from

being tightened to the specified torque.

1. Install a new seal onto the end of each injec-

tor.

2. Install the injectors “1” to the fuel rails “2”.
3. Install the secondary injector joint “3”, making

sure to install them in the correct direction.

4. Install the injector assemblies to the air filter

case cover.

A. Upper
B. Lower

Intake funnel assembly bolt

8 Nm (0.8 m·kgf, 5.8 ft·lbf)

A. Upper
B. Lower

Fuel rail screw (secondary injec-

tor)

3.5 Nm (0.35 m·kgf, 2.5 ft·lbf)

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды