Yamaha R1 Series 2015 Скачать руководство пользователя страница 420 | Manualshive

Страница: 420 / 704

Yamaha R1 Series 2015 Скачать руководство пользователя страница 420

CONNECTING RODS AND PISTONS

5-79

1. Install:

•

Big end bearings

•

Connecting rod cap
(onto the connecting rod)

TIP

•

Clean the big end bearings, crankshaft pins,
and the connecting rods with oil cleaner, and
then wait five minutes to dry the remaining oil
cleaner component.

•

When cleaning the connection rod, clean the
bearing surface “a” of the connecting rod bolt
and threads “b”.

•

Be sure to reinstall each big end bearing in its
original place.

•

Align the projections “c” on the big end bear-
ings with the notches “d” in the connecting rods
and connecting rod caps.

•

Make sure that the projection “e” on the con-
necting rod cap faces the same direction as the
“Y” or “ ” mark “f” on the connecting rod.

2. Tighten:

•

Connecting rod bolts

NOTICE

ECA18390

Tighten the connecting rod bolts using the

plastic-region tightening angle method. Al-

ways install new bolts.

TIP

•

Install by carrying out the following procedures
in order to assemble in the most suitable con-
dition.

•

Install the new connecting rod bolt without
cleaning and without any oil.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Replace the connecting rod bolts with new

ones.

b. After installing the big end bearing, assemble

the connecting rod and connecting rod cap
without installing them onto the crankshaft.

c. Tighten the connecting rod bolt while check-

ing that the sections shown “a” and “b” are
flush with each other by touching the surface.

TIP

To install the connecting rod cap, care should be
taken not to install it at an angle and the position
should not be out of alignment.

d. Loosen the connecting rod bolt, remove the

connecting rod and connecting rod cap and
install these parts to the crankshaft with the
big end bearing kept in the current condition.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

3. Install:

•

Oil ring expander “1”

•

Lower oil ring rail “2”

•

Upper oil ring rail “3”

a

b

c

d

e

f

Connecting rod bolt

30 Nm (3.0 m·kgf, 22 ft·lbf)

a. Side machined face
b. Thrusting faces

New

T

R

.

.

a

b

«
...
418
419
420
421
422
...
»

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов