Yamaha R1 Series 2015 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 704

background image

FEATURES

1-34

left to right and highlight the item you want to
adjust.

2. Use the mode switch up button or down but-

ton to change the selected item value (verti-
cal scrolling is not possible).

TIP

•

When the vehicle is in motion, YRC items
MODE, TCS, and SCS cannot be adjusted.

•

When the throttle grip is being turned PWR
cannot be adjusted.

•

When YRC items MODE/PWR/TCS/SCS can-
not be adjusted, the respective YRC item box
changes to white.

•

To turn off the traction control system select
TCS with the center button, then push and hold
the up button until TCS OFF is displayed. To
turn TCS back on, select TCS OFF and then
press the down button (TCS will return to its
previous setting).

•

Turning off the traction control system will turn
off the SCS, LCS, and LIF systems for all YRC
modes.

YRC items LCS/QS/LIF

The on/off status of YRC items LCS, QSS, and
LIF is shown here. When any of these systems
are registered (not set to OFF) for the currently
selected YRC mode, its respective icon will ap-
pear.
When LCS is registered for the currently select-
ed YRC mode, its icon will be grey. To activate
the launch control system, press and hold the
center button until the LCS icon stops flashing
and turns white.

TIP

LCS, QSS, and LIF system setting levels can
only be adjusted from the MENU screen.

ERS indicator (YZF-R1M)

This icon shows the current ERS mode. (Refer
to “YRC Setting” on page 1-37 and “ERS (YZF-
R1M)” on page 1-39 to change the registered
ERS mode or adjust ERS setting levels.)

TIP

The ERS indicator will flash should the SCU
need to be reset, but this does not indicate a
malfunction.

•

The suspension will remain fixed at its most re-
cent settings until the SCU is reset.

•

To reset the SCU, stop the vehicle and turn the
key to “OFF” then “ON”.

GPS indicator (CCU-equipped models)

This icon comes on when a GPS unit is synched
with your vehicle.

Logging indicator (CCU-equipped models)

This icon comes on when vehicle data is being
recorded via the logging function.

Lap timer

This stopwatch function measures and records
up to forty laps. On the main screen, the lap tim-
er shows the current lap time and lap number
(indicated by the LAP mark). Use the PASS-
ING/LAP switch to mark lap times. When a lap is
completed, the lap timer will show the latest lap
time (marked by the LATEST indicator) for five
seconds.

[To use the lap timer]

1. Short push the wheel switch. The information

display item will flash for five seconds.

2. While the information display item is flashing,

rotate the wheel switch upward. The lap timer
will flash for five seconds.

3. While the lap timer is flashing, long push the

wheel switch to activate the lap timer or stop
the lap timer.

1. Mode switch “MODE”
2. Up button
3. Center button
4. Down button

1

2

4

3

1. Lap time
2. Latest lap time indicator “LATEST”
3. Information display item
4. Lap number

MODE-

A

PWR

1

TCS

3

SCS

2

km/h

123

ODO

km

7890

GEAR

N

LAP

03

LATEST

40

03 06

×

1000 r/min

A-2

QS

LIF

GPS

12:00

ABERAGE

4

1

2

3

«
...
41
42
43
44
45
...
»

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R1 Series 2015

Versaflo M Series

Бренд: 3M Страницы: 27

Speedglas 9100 Series

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 5

Бренд: Würth Страницы: 188

Pulsar 135 BS VI

Бренд: Bajaj Страницы: 48

Бренд: Yoshimura Страницы: 4

Бренд: Pandora Страницы: 56

Бренд: Two Brothers Racing Страницы: 2

WOLVERINE X4 2021

Бренд: Yamaha Страницы: 192

Бренд: Yamaha Страницы: 224

Бренд: Yamaha Страницы: 343

Бренд: Yamaha Страницы: 404

Бренд: Yamaha Страницы: 432

Бренд: Yamaha Страницы: 404

Бренд: Yamaha Страницы: 694

Бренд: Yamaha Страницы: 864

Бренд: Yamaha Страницы: 912

Бренд: Yamaha Страницы: 864

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды