Yamaha R1 Series 2015 Скачать руководство пользователя страница 139 | Manualshive

Страница: 139 / 704

background image

CABLE ROUTING

2-64

1. Steering damper solenoid coupler (OHLINS:

OPTION)

2. SCU lead (sub-wire harness)
3. Intake air temperature sensor
4. Sub-wire harness (SCU, steering damper

solenoid, sub-wire harness)

5. Auxiliary light lead
6. Sub-wire harness (front fork stepping motor)
7. Plastic locking tie
8. Front turn signal light lead (left)
9. Clamp
10.Wire harness
11.Intake solenoid vacuum hose
12.Front turn signal light lead (right)
13.SCU (Suspension Control Unit)
14.Steering damper solenoid lead

A. The steering damper solenoid coupler

(OHLINS: OPTION) may be positioned in any

place.

B. To front left turn signal light
C. Route the sub-wire harness (SCU, steering

damper solenoid, sub-wire harness) to the

left side of the fuse box 1, and then connect

to the wire harness.

D. Fasten the sub-wire harness and intake sole-

noid vacuum hose with the plastic locking tie.

Make sure that the end of the plastic locking

tie does not protrude above the intake sole-

noid vacuum hose.

E. Connect the coupler of the sub-wire harness

(front fork stepping motor) to the coupler of

the sub-wire harness (SCU, steering damper

solenoid, sub-wire harness).

F. Fasten the intake solenoid vacuum hose,

front left turn signal light lead, and auxiliary

light lead at the outside of the fuse box 1 with

the clamp.

G. Fasten the intake solenoid vacuum hose onto

the wire harness with the plastic locking tie.

Face the buckle of the plastic locking tie out-

ward. (2 locations)

H. Place the sub-wire harness to the outside of

the intake solenoid vacuum hose, and then

fasten it with the plastic locking tie.

I. Install the SCU coupler and coupler cover

securely to the SCU. Make sure that the

edges of the coupler cover are not rolled up.

J. To front right turn signal light
K. Connect the front right turn signal light cou-

pler, and then fasten the front right turn signal

light leads with the clamp. The leads may be

positioned in any order within the clamp.

L. To intake solenoid
M. To front fork

«
...
137
138
139
140
141
...
»

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R1 Series 2015

Бренд: DAELIM Страницы: 2

Бренд: Yamaha Страницы: 88

Apache RTR 160 HYPER EDGE 2015

Бренд: TVS Страницы: 60

Бренд: Yamaha Страницы: 88

Бренд: R&G Страницы: 15

Бренд: Cobra Страницы: 38

Бренд: DUCATI Performance Страницы: 9

Бренд: Suzuki Страницы: 89

Бренд: GYS Страницы: 36

Бренд: thousand Страницы: 32

Бренд: hepco & becker Страницы: 2

Бренд: RDMOTO Страницы: 2

Бренд: X-lite Страницы: 84

Бренд: Free Spirits Страницы: 28

690 Enduro AUS 2010

Бренд: KTM Страницы: 265

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды