Yamaha R1 Series 2015 Скачать руководство пользователя страница 458 | Manualshive

Страница: 458 / 704

background image

AIR FILTER CASE

7-5

EAS30458

CHECKING THE SECONDARY INJECTORS

(BEFORE REMOVING)

1. Check:

•

Injectors
Use the diagnostic code numbers “40”–“43”.
Refer to “SELF-DIAGNOSTIC FUNCTION
AND DIAGNOSTIC CODE TABLE (ECU)” on
page 9-5.

EAS30459

REMOVING THE FUEL HOSE (PRIMARY

INJECTOR JOINT SIDE AND SECONDARY

INJECTOR JOINT SIDE)

1. Remove:

•

Fuel hose (primary injector joint side and sec-
ondary injector joint side)

WARNING

EWA17320

Cover fuel hose connections with a cloth

when disconnecting them. Residual pres-

sure in the fuel lines could cause fuel to

spurt out when removing the hose.

NOTICE

ECA17490

Be sure to disconnect the fuel hose by hand.

Do not forcefully disconnect the hose with

tools.

TIP

•

To remove the fuel hose from the secondary
injector joint, slide the fuel hose connector cov-
er “1” on the end of the hose in the direction of
the arrow shown, press the two buttons “2” on
the sides of the connector, and then remove
the hose.

•

Before removing the hose, place a few rags in
the area under where it will be removed.

EAS30460

REMOVING THE SECONDARY INJECTORS

WARNING

EWA17330

• Check the injectors in a well-ventilated area

free of combustible materials. Make sure

that there is no smoking or use of electric

tools in the vicinity of the injectors.

• Be careful when disconnecting the fuel

hose. Any remaining pressure in the fuel

hose may cause the fuel to spray out. Place

a container or rag under the hose to catch

any fuel that spills. Always clean up any

spilt fuel immediately.

• Turn the main switch to “OFF” and discon-

nect the negative battery lead from the bat-

tery terminal before removing the injectors.

1. Remove:

•

Fuel tank

•

Fuel hose
Refer to “REMOVING THE FUEL TANK” on
page 7-2.

2. Remove:

•

Fuel rail screw “1”

•

Fuel rail “2”

•

Secondary injector joint “3”

•

Secondary injector “4”

EAS31663

REMOVING THE AIR FILTER CASE

1. Remove:

•

Air filter case cover

2. Loosen:

•

Intake funnel assembly bolt “1”

1

2

1

2

3

4

1

4

2

«
...
456
457
458
459
460
...
»

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R1 Series 2015

Бренд: Yamaha Страницы: 860

Бренд: klicbag Страницы: 2

Бренд: Sym Страницы: 31

Бренд: PEUGEOT Страницы: 12

V125 Special 2018

Бренд: Lambretta Страницы: 53

Бренд: DYNATEK Страницы: 5

Бренд: DYNATEK Страницы: 4

Бренд: Montesa Страницы: 114

4Ride MST260 2016

Бренд: Montesa Страницы: 158

Бренд: IBEX Страницы: 2

Бренд: R&G Страницы: 9

Lectra VR24 1998

Бренд: EMB Страницы: 58

Бренд: MARLINK Страницы: 3

Бренд: Wunderkind Custom Страницы: 16

Бренд: Sealey Страницы: 2

Бренд: Hermes Страницы: 23

98-13 Road Glide/Ultra

Бренд: Sinister Sound Страницы: 14

Бренд: Honda Страницы: 264

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды