Yamaha R1 Series 2015 Скачать руководство пользователя страница 534 | Manualshive

Страница: 534 / 704

background image

FUEL INJECTION SYSTEM

8-53

Features of the Yamaha diagnostic tool
You can use the Yamaha diagnostic tool to identify malfunctions quicker than with conventional-
methods.
By connecting the adapter interface, which is connected to the USB port of a computer, to a vehicle’s
ECU using the communication cable, you can display information that is necessary for identifying mal-
functions and for maintenance to display on the computer. The displayed information includes the sen-
sor output data and information recorded in the ECU.
Functions of the Yamaha diagnostic tool

However, the diagnostic tool cannot be used to freely change the basic vehicle functions, such as ad-
justing the ignition timing.
Connecting the Yamaha diagnostic tool
Remove the protective cap “1”, and then connect the Yamaha diagnostic tool to the coupler.

TIP

When the Yamaha diagnostic tool is connected to the vehicle, the operation of the multi-function meter
and indicators will be different from the normal operation.

Yamaha diagnostic tool

90890-03239

Fault diagnosis mode:

Fault codes recorded on the ECU are read, and the contents are dis-

played.

The freeze frame data (FFD) is the operation data when a malfunction

was detected. This data can be used to identify when the malfunction

occurred and check the engine conditions and running conditions when

it occurred.

Function diagnostic mode:

Check the operation of the output value of each sensor and actuator.

Inspection mode:

Determine whether each sensor or actuator is functioning properly.

CO adjustment mode:

Adjust the concentration of CO admissions during idling.

Monitoring mode:

Displays a graph of sensor output values for actual operating condi-

tions.

Logging mode:

Records and saves the sensor output value in actual driving conditions.

View log:

Displays the logging data.

ECU rewrite:

If necessary, the ECU is rewritten using ECU rewrite data provided by

Yamaha.

Ignition timing adjustment, etc. cannot be changed from the vehicle’s

original state.

1

«
...
532
533
534
535
536
...
»

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R1 Series 2015

Бренд: Dakota Digital Страницы: 6

Rocky Mountain-EXP SB-1

Бренд: Wolfman Страницы: 7

Бренд: R&G Страницы: 9

SPORTCITY CUBE 125

Бренд: APRILIA Страницы: 157

Бренд: Honda Страницы: 243

Бренд: Yamaha Страницы: 126

Бренд: Takegawa Страницы: 2

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 8

Бренд: HAUL MASTER Страницы: 8

Бренд: B&G electronics Страницы: 5

Бренд: Brixton Страницы: 148

Бренд: hepco & becker Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды