manualshive.com logo in svg

Yamaha R1 Series 2015, Руководство по обслуживанию, Страница: 133 / 704

Поделиться
Скачать
Yamaha R1 Series 2015 Скачать руководство пользователя страница 133

CABLE ROUTING

2-58

1. Intake funnel servo motor lead
2. Right handlebar switch lead (non-waterproof 

2-pole)

3. Left handlebar switch lead (non-waterproof 4-

pole)

4. Right handlebar switch lead (non-waterproof 

6-pole)

5. Right handlebar switch lead (waterproof 4-

pole)

6. Main switch lead (1-pole)
7. Main switch lead (2-pole)
8. Radiator fan motor relay lead
9. Left handlebar switch lead (waterproof 10-

pole)

10.Headlight control unit
11.Headlight control unit lead
12.Turn signal light lead (left)
13.Radiator fan motor lead (right) (black)
14.Radiator fan motor lead (left) (white)
15.Rectifier/regulator lead
16.Electrical components tray
17.Plastic locking tie
18.Secondary injector #4
19.Secondary injector #3
20.Secondary injector #2
21.Secondary injector #1
22.Secondary injector lead
23.Right handlebar switch lead
24.Left handlebar switch lead
25.Main switch lead
26.Fuel rail

A.  Connect the intake funnel servo motor lead 

on top of the frame, and then place it 

between the air filter case and frame.

B.  Route the leads (main harness side) from 

front of the rib “D” on the electrical compo-

nents tray to the inside.

Connect the leads to the wire harness, and 

then fasten the coupler to the electrical com-

ponents tray.

C.  Route the radiator fan motor relay lead and 

main switch lead (2-pole) to the rear of the rib 

“D” on the electrical components tray.

Route the main switch lead (1-pole) from 

front of the rib “D” on the electrical compo-

nents tray to the inside.

D.  Rib on the electrical components tray
E.  Connect the headlight control unit lead at the 

top to the headlight control unit.

F.  To intake solenoid
G. To front left turn signal light
H.  The radiator fan motor couplers may be 

installed to the electrical components tray in 

any order.

Route the radiator fan motor lead to the rear 

of the main switch lead and left handlebar 

switch lead as shown in the illustration.

I.  When installing the plastic locking tie to the 

electrical components tray, position it in the 

center within the range shown in the illustra-

tion.

J.  Fit the secondary injector lead at the white 

tape between the ribs of the air filter case.

K.  Route the secondary injector lead between 

the air filter case and cross bar.

L.  Fasten the leads along the electrical compo-

nents tray with the plastic locking tie so that 

they do not overlap one another.

Face the buckle of the plastic locking tie 

upward. Do not cut off the excess end of the 

plastic locking tie.

M. The left handlebar switch lead and main 

switch lead may be routed in any order.

N.  Fasten the right handlebar switch lead and 

electrical components tray with the plastic 

locking tie. Face the buckle of the plastic lock-

ing tie rearward, and then cut off the excess 

end of the tie to 5 mm (0.2 in) or less.

O.  Fasten the injector lead and fuel rail with the 

plastic locking tie. Point the end of the plastic 

locking tie rearward. Do not cut off the excess 

end of the plastic locking tie.

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов