manualshive.com logo in svg

Yamaha R1 Series 2015, Руководство по обслуживанию, Страница: 149 / 704

Поделиться
Скачать
Yamaha R1 Series 2015 Скачать руководство пользователя страница 149

CABLE ROUTING

2-74

1. Hydraulic unit
2. Rear frame
3. Brake fluid reservoir
4. Frame
5. Brake hose (rear brake master cylinder to 

hydraulic unit)

6. Rear wheel sensor lead
7. Rear brake master cylinder
8. Swingarm assembly
9. Rear wheel sensor lead cover
10.Rear wheel sensor protector
11.Rear wheel sensor
12.Rear brake caliper
13.Brake hose (hydraulic unit to rear brake cali-

per)

14.Brake fluid reservoir hose
15.Hydraulic unit brake pipe (rear brake master 

cylinder to hydraulic unit)

16.Hydraulic unit brake pipe (hydraulic unit to 

rear brake caliper) 

17.Rear brake hose bracket
18.Clamp
19.Hook
20.Brake caliper bracket
21.Rear brake hose holder
22.Rear fender

A.  Install the clamp 0–10 mm (0–0.39 in) from 

the slit of the brake hose protector.

B.  Make sure that the rear wheel sensor lead 

does not protrude from the rear wheel sensor 

lead cover.

C.  Route the rear wheel sensor lead between 

the swing arm assembly and rear wheel sen-

sor lead cover.

D.  65.4

q

E.  58.6

q

F.  Position the rear wheel sensor lead at the 

back.

G. Install the clamp at a position 0–10 mm (0–

0.39 in) from the top edge of the brake hose 

protector.

H.  Fasten the rear wheel sensor lead at under 

the white tape with the clamp.

I.  Fasten the brake hose (rear brake master cyl-

inder to hydraulic unit) at the metal fitting with 

large inner diameter side of the clamp.

J.  Install the grommet of the rear wheel sensor 

lead securely to the hook.

When installing the grommet on the rear 

wheel sensor lead, may apply silicone fluid or 

soapy water to the grommet.

K.  Install the grommet of the rear wheel sensor 

lead securely to the claw of the rear wheel 

sensor lead cover.

When installing the grommet on the rear 

wheel sensor lead, may apply silicone fluid or 

soapy water to the grommet.

L.  Install the grommet of the rear wheel sensor 

lead securely to the rear wheel sensor pro-

tector.

When installing the grommet on the rear 

wheel sensor lead, may apply silicone fluid or 

soapy water to the grommet.

M. Install the rear wheel sensor lead securely to 

the claw of the rear wheel sensor protector.

N.  Route the brake hose between the rear brake 

hose holder and swing arm assembly.

O.  Fasten the brake hose with the clamp.

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов