Yamaha R1 Series 2015 Скачать руководство пользователя страница 372

Страница: 372 / 704

VALVES AND VALVE SPRINGS

5-31

b. Install the valve into the cylinder head.
c. Press the valve through the valve guide and

onto the valve seat to make a clear impres-
sion.

d. Measure the valve seat contact width.

TIP

Where the valve seat and valve face contacted
one another, the blue layout fluid will have been
removed.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

4. Lap:

•

Valve face

•

Valve seat

TIP

After replacing the cylinder head or replacing the
valve and valve guide, the valve seat and valve
face should be lapped.

NOTICE

ECA22580

This model uses titanium intake valves.

Titanium valves that have been used to lap

the valve seats must not be used. Always re-

place lapped valves with new valves.

TIP

•

When replacing the intake valves, replace the
intake valves without lapping the valve seats
and valve faces.

•

When replacing the cylinder head or intake
valve guides, use new valves to lap the valve
seats, and then replace them with new intake
valves.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Apply a coarse lapping compound “a” to the

valve face.

NOTICE

ECA13790

Do not let the lapping compound enter the

gap between the valve stem and the valve

guide.

b. Apply molybdenum disulfide oil onto the

valve stem.

c. Install the valve into the cylinder head.
d. Turn the valve until the valve face and valve

seat are evenly polished, then clean off all of
the lapping compound.

TIP

For the best lapping results, lightly tap the valve
seat while rotating the valve back and forth be-
tween your hands.

e. Apply a fine lapping compound to the valve

face and repeat the above steps.

f. After every lapping procedure, be sure to

clean off all of the lapping compound from the
valve face and valve seat.

g. Apply blue layout fluid “b” onto the valve face.

h. Install the valve into the cylinder head.
i. Press the valve through the valve guide and

onto the valve seat to make a clear impres-
sion.

j. Measure the valve seat contact width “c”

again. If the valve seat width is out of specifi-

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Yamaha R1 Series 2015, Руководство по обслуживанию, Страница: 372 / 704

Результаты поиска

Содержание R1 Series 2015

Отзывы: