Yamaha R1 Series 2015 Скачать руководство пользователя страница 188

Страница: 188 / 704

PERIODIC MAINTENANCE

3-14

EAS30801

CHECKING THE BRAKE OPERATION

1. Check:

•

Brake operation
Brake not working properly

Check the

brake system.
Refer to “FRONT BRAKE” on page 4-43 and
“REAR BRAKE” on page 4-55.

TIP

Drive on the dry road, operate the front and rear
brakes separately and check to see if the brakes
are operating properly.

EAS30632

CHECKING THE BRAKE FLUID LEVEL

1. Stand the vehicle on a level surface.

TIP

•

Place the vehicle on a suitable stand.

•

Make sure the vehicle is upright.

2. Check:

•

Brake fluid level
Below the minimum level mark “a”

Add the

specified brake fluid to the proper level.

WARNING

EWA13090

• Use only the designated brake fluid. Other

brake fluids may cause the rubber seals to

deteriorate, causing leakage and poor

brake performance.

• Refill with the same type of brake fluid that

is already in the system. Mixing brake fluids

may result in a harmful chemical reaction,

leading to poor brake performance.

• When refilling, be careful that water does

not enter the brake fluid reservoir. Water

will significantly lower the boiling point of

the brake fluid and could cause vapor lock.

NOTICE

ECA13540

Brake fluid may damage painted surfaces

and plastic parts. Therefore, always clean up

any spilt brake fluid immediately.

TIP

In order to ensure a correct reading of the brake
fluid level, make sure the top of the brake fluid
reservoir is horizontal.

EAS30630

ADJUSTING THE FRONT DISC BRAKE

1. Adjust:

•

Brake lever position
(distance “a” from the throttle grip to the brake
lever)

TIP

•

While pushing the brake lever forward, turn the
adjusting dial “1” until the brake lever is in the
desired position.

•

Be sure to align the setting on the adjusting dial
with the arrow mark “2” on the brake lever hold-
er.

Front brake

Specified brake fluid

DOT 4

Rear brake

Specified brake fluid

DOT 4

A. Front brake
B. Rear brake

Position #1

Distance “a” is the largest.

Position #6

Distance “a” is the smallest.

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды

Yamaha R1 Series 2015, Руководство по обслуживанию

Результаты поиска

Содержание R1 Series 2015

Отзывы:

Похожие инструкции для R1 Series 2015

Бренды по названию

Популярные бренды