Yamaha R1 Series 2015 Скачать руководство пользователя страница 222 | Manualshive

Страница: 222 / 704

background image

GENERAL CHASSIS (1)

4-5

EAS31636

INSTALLING THE IMU

NOTICE

ECA22611

• Do not perform angle adjustment of the IMU

and battery box by pinching the washer

and related parts.

• When installing the IMU, apply a thin coat of

silicone grease onto the washer where con-

tacting the IMU grommet.

• When installing the IMU, use only a genuine

bolt and washer, and tighten the bolt to the

specified torque.

• Pay attention not to expose the IMU to

strong shocks, such as striking or drop-

ping it.

• Do not place any foreign objects in and

around the battery box.

• Do not obstruct breather opening “a” of the

IMU.

• Do not clean the breather opening and do

not blow it with compressed air.

• When replacing the collar or grommet, re-

place all four collars and grommets.

1. Install:

•

IMU (Inertial Measurement Unit) “1”

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the IMU coupler “2” to the IMU.
b. Install the IMU “1”, washers and IMU bolts,

and then tighten the bolts to specification.

TIP

Apply a thin coat of silicone grease onto the
washers where contacting the grommets.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS31676

CONNECTING TO THE CCU (for YZF-R1M)

The  CCU  (Communication  Control  Unit)  con-
nects to the vehicle’s CAN (Controller Area Net-
work)  and  has  a  GPS  receiver  to  enable  the
recording  of  vehicle  and  riding  data.  (Refer  to
“MENU SCREEN” on page 1-36.) Logging data
and YRC setting data can be accessed when a
smartphone, tablet, or laptop computer is con-
nected to the CCU wireless network.

TIP

From the Google© application store, download
the “Y-TRAC” application to make use of the log-
ging data and the “YRC Setting” application to
remotely adjust the YRC settings.

1. Connect:

•

CCU wireless network

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the bolts “1” and then remove the

passenger seat cover assembly “2” as
shown.

b. Note down the CCU serial number “a”.

Recommended lubricant

Silicone grease

IMU bolt

2.0 Nm (0.20 m·kgf, 1.4 ft·lbf)

a

T

R

.

.

S

1

2

S

1

1

2

«
...
220
221
222
223
224
...
»

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R1 Series 2015

Speedglas G5-02

Бренд: 3M Страницы: 17

Speedglas 9100 MP

Бренд: 3M Страницы: 72

Бренд: 3M Страницы: 84

Бренд: R&G Страницы: 21

Бренд: thousand Страницы: 32

Бренд: GAS GAS Страницы: 131

V125 Special 2018

Бренд: Lambretta Страницы: 53

Бренд: Ecomobility Green World Страницы: 24

Бренд: KTM Страницы: 7

Бренд: Ice Bear Страницы: 64

Бренд: X&I Страницы: 59

Бренд: Shark Страницы: 18

Бренд: Montesa Страницы: 114

4Ride MST260 2016

Бренд: Montesa Страницы: 158

POCKET BIKE QG-40

Бренд: Coolster Страницы: 13

RR 125 2T MY 2018

Бренд: Beta Motorcycles Страницы: 138

Бренд: Beta Страницы: 74

Бренд: Vetter Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды