manualshive.com logo in svg

Yamaha R1 Series 2015, Руководство по обслуживанию, Страница: 183 / 704

Поделиться
Скачать
Yamaha R1 Series 2015 Скачать руководство пользователя страница 183

PERIODIC MAINTENANCE

3-9

•

Align the camshaft sprocket marks with the cyl-
inder head surface.

•

If the camshaft cap bolt is a new one, it is not
necessary to apply engine oil onto the mating
surface and threads of the bolt.

•

If the camshaft cap bolt is a new one, tighten it
to 10 Nm (1.0 m·kgf, 7.2 ft·lbf).

•

Turn the crankshaft counterclockwise several
full turns to seat the parts.

h. Measure the valve clearance again.
i. If the valve clearance is still out of specifica-

tion, repeat all of the valve clearance adjust-
ment  steps  until  the  specified  clearance  is
obtained.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

7. Install:

•

All removed parts

TIP

For installation, reverse the removal procedure.

EAS31017

CHECKING THE ENGINE IDLING SPEED

TIP

Prior  to  checking  the  engine  idling  speed,  the
throttle body synchronization should be adjusted
properly, the air filter element should be clean,
and the engine should have adequate compres-
sion.

1. Start the engine and let it warm up for several

minutes.

2. Check:

•

Engine idling speed
Out of specification 

o

 Go to next step.

3. Check:

•

ISC (Idle Speed Control) learning value
“00” or “01” 

o

 Check the intake system.

“02” 

o

 Clean the throttle bodies.

Refer to “CHECKING AND CLEANING THE
THROTTLE BODIES” on page 7-12.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the Yamaha diagnostic tool. 

Use the diagnostic code number “67”.
Refer  to  “SELF-DIAGNOSTIC  FUNCTION
AND DIAGNOSTIC CODE TABLE (ECU)” on
page 9-5.

b. Check the ISC (Idle Speed Control) leaning

value.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS30797

SYNCHRONIZING THE THROTTLE BODIES

TIP

Before synchronizing the throttle bodies, check
the following items:

•

Valve clearance

•

Spark plugs

•

Air filter element

•

Throttle body joints

•

Fuel hose

•

Exhaust system

•

Breather hoses

Checking the throttle body synchronization

1. Stand the vehicle on a level surface.

TIP

Place the vehicle on a suitable stand.

2. Remove:

•

Rider seat
Refer to “GENERAL CHASSIS (1)” on page
4-1.

•

Fuel tank cover
Refer to “GENERAL CHASSIS (2)” on page
4-7.

•

Fuel tank
Refer to “FUEL TANK” on page 7-1.

•

Air filter case
Refer to “AIR FILTER CASE” on page 7-4.

3. Remove:

•

Caps “1”

4. Install:

•

Vacuum gauge “1”

Engine idling speed

1200–1400 r/min

Vacuum gauge

90890-03094

Vacuummate

YU-44456

1

Содержание R1 Series 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов