138
wallaceperimetersecurity.com
Phone: 866.300.1110
REFERENCE
Reference
This section of the manual provides information which may be useful when installing Kinetic operators. It
includes how to:
•
Connect a Radio Receiver for Remote Open
•
Install a Gate Locking Mechanism
•
Set User Relay Functions
•
Install Vehicle Detectors and Loops
•
Install Photoelectric Sensors
•
Install Gate Edge Sensors
•
Troubleshoot Error Codes, Faults, and
Hardware Issues
•
Diagnose Vehicle Detector and Loop Faults
•
Handle General Maintenance Procedures
Connecting a Radio Receiver for Remote Open
Take the following steps to mount a commercial style 24VDC radio receiver (external antenna type):
1.
Install the receiver in the channel of the chassis on either side of the control box.
2.
Knock out the closest hole in the bottom of the control box and route the wires to the area marked
RADIO OPTIONS. Only three wire connections are needed because the common wire and one radio
output wire are connected together. Figure 36 shows additional wires from a two-channel receiver.
3.
Make sure to observe polarity and crimp together the black radio common wire and one of the radio
output wires using a ¼ -inch spade connector.
4.
Fasten the two crimped wires to the COM terminal.
5.
Connect the red wire to the +24V spade and connect the other radio output contact wire to the spade
marked OPEN.
NOTE:
This terminal is the same as the input terminal labelled RADIO OPEN along the left edge of the
SmartDC Controller.
6.
Mount an external antenna onto the top of a fixed fence post near the operator.
7.
Connect the antenna into the socket on the radio receiver.
8.
Set the “DIP” switches in the receiver to match the same code used in the transmitter.
Figure 36
.
Additional Wires from Two-Channel Receiver
If an edge sensor transmitter is also
used to reverse the gate, be certain
to use a two
-
channel commercial
receiver. The edge and handheld
transmitters must have their codes
set to match the receiver or they will
not function.
Содержание ALPHA
