Tuttnauer Elara11 Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 109

background image

Page 102

Problem/
Error
Message

Message / Symbol Description

Corrective Action

"Chamber
pressure not
in range"

This message is displayed if the
pressure in the chamber is higher
or lower than the normal range.

Wait until the chamber
reaches the normal
pressure range.
The atmospheric
pressure parameter may
need to be set. See
section 5.2.3.1

"I/O Card
Failed"

This message is displayed if I/O
card is faulty (both while cycle is
running or not).

Turn the unit off and then
back on. If the message
reappears Call for service

"I/O card is
not
connected"

This message is displayed if the
main control board has lost
communication with the I/O card.
(both while cycle is running or not).

Turn the unit off and then
back on. If the message
reappears Call for service

"Low Temp"

This message is displayed if the
temperature drops below the
sterilization temperature for more
than 1 second during sterilization
cycle.

Perform a new cycle. The
chamber may be
overloaded, remove some
material from the
chamber.
Check for steam leakage
around the door. Clean or
replace the door gasket if
necessary. If the problem
persists, call for service

"High Temp"

This message is displayed if the
temperature raises 5.4°F (3°C)
above sterilization temperature
during the sterilization stage for 2
seconds during sterilization cycle.

Perform a new cycle. If
the problem persists, call
for service.

"High Temp.
(Ending)"

This message is displayed if the
chamber cannot reach the required
ending temperature within 10
minutes.

Verify that the autoclave
is not overloaded.
Remove some material
from the chamber
Perform a new cycle. If
the problem persists, call
for service.

"Heat Time
Error"

This message is displayed if the
chamber cannot reach the required
temperature within the preset time.

Verify that the autoclave
is not overloaded, remove
some material, and
perform another cycle.
The atmospheric
pressure parameter may
need to be set. See
section
5.2.3.1. If the problem
persists, call for service.

«
...
101
102
103
104
105
...
»

Содержание Elara11














































































































Отзывы:

Нет отзывов

Похожие инструкции для Elara11

Бренд: ABB Страницы: 18

Бренд: R-Tech Страницы: 3

Бренд: ZOLL Страницы: 5

Бренд: Accu-Chek Страницы: 3

Бренд: iBin Страницы: 2

Бренд: Hanil Страницы: 60

Бренд: Palazzetti Страницы: 112

Бренд: MacDon Страницы: 2

Бренд: MacDon Страницы: 214

Бренд: MacDon Страницы: 32

Бренд: Yamaha Страницы: 50

Бренд: A&D Страницы: 30

Бренд: Zempire Страницы: 2

Бренд: HALDER Страницы: 2

Бренд: Hakko Electronics Страницы: 16

Бренд: Valko Страницы: 10

Sonorex Super RK 31

Бренд: BANDELIN Страницы: 21

BTL7-A/E501-M Series

Бренд: Balluff Страницы: 194

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды