6A1-60 ENGINE MECHANICAL (G16 ENGINE)
c) Stamped number on piston and that on cylinder block
should correspond. That is, install number 2 stamped pis-
ton to cylinder which is identified with number 2 and a num-
ber 1 piston to cylinder with number 1.
Piston and Cylinder specification
Also, a letter A, B or C is stamped on piston head but ordinarily it
is not necessary to discriminate each piston by this letter.
1) Install piston pin to piston (1) and connecting rod (3) :
After applying engine oil to piston pin and piston pin holes in
piston and connecting rod, fit connecting rod to piston as
shown in figure and insert piston pin to piston and connect-
ing rod, and install piston pin circlips.
2) Install piston rings to piston :
• 1st ring (1) differs from 2nd ring (2) in shape and marking.
Distinguish 1st ring from 2nd ring by referring to figure, and
install these piston rings to piston directing marked side of
each ring toward top of piston.
• When installing oil ring (3), install spacer first and then two
rails.
Piston
Cylinder
Piston-to-
cylinder
clearance
Num-
ber at
the top
(mark)
Outer diame-
ter
Num-
ber
(mark)
Bore diame-
ter
1
74.9801 –
74.9900 mm
(2.9520 –
2.9523 in.)
1
75.0101 –
75.0200 mm
(2.9531 –
2.9535 in.)
0.02 – 0.04
mm (0.0008
– 0.0015 in.)
2
74.9700 –
74.9800 mm
(2.9516 –
2.9519 in.)
2
75.0000 –
75.0100 mm
(2.9528 –
2.9531 in.)
0.02 – 0.04
mm (0.0008
– 0.0015 in.)
NOTE:
Circlip should be installed with its cut part facing either
up or down as shown in figure.
2. Arrow mark
4. Oil hole
A. Crankshaft pulley side
Содержание Engine 2002 GRAND VITARA SQ625
