manualshive.com logo in svg

St. Jude Medical QUANTIEN, Инструкция по эксплуатации

Поделиться
Скачать
St. Jude Medical QUANTIEN Скачать руководство пользователя страница 20

 

16 

 

 

Powering On and Shutting Down 

Powering On 
Check that the mains cable is connected to the power supply unit and to the mains power outlet. 
Press the power switch on the bottom panel to start the QUANTIEN™ measurement system. 
The screen will remain dark for a few seconds before a startup beep indicates that the system is 
booting up. 
When the status check is OK, indicated by blue checkmarks, the 

User Login

 window appears. 

Enter your credentials to log into the system. See User Settings for more information (page 35). 

WARNING: Do not leave the QUANTIEN measurement system unattended while 
logged in as a Site Administrator. 

NOTE: If you do not have credentials to log into the system, you can log in as "guest". 

After login, the 

Select Room

 window appears. If a room configuration is set as default then the 

first screen will be the 

Patient

 menu. Select 

Skip 

to move to the   

(Setup) 

menu where any 

menu can be selected. 
At interruption of supply mains for less than 5 minutes an ongoing examination can be continued 
seamlessly provided that both Pa and Pd have been zeroed before power was lost. After power 
recovery you will be asked if the previous examination shall be continued. If you select to 
continue, the examination will continue. Otherwise the system will perform a normal start up. If 
supply mains is interrupted for more than 5 minutes, the QUANTIEN measurement system will 
always perform a normal start up. 

Shutting Down 
Press the switch on the bottom panel to OFF to shut down. 

CAUTION: The power switch will shut down the QUANTIEN™ measurement 
system but there is still power in the mains cable and power supply unit. To fully 
disconnect from mains power, remove the mains power plug from the wall socket. 

Room Configuration 

After logging into the QUANTIEN™ measurement system, the 

Select Room 

window should open 

(alternatively select the   

(Setup)

 Menu, choose

 Select Room 

to open the 

Room 

window). 

In the 

Select Room

 window a button for each transmitting Wi-Box™ AO transmitter within radio 

range of the QUANTIEN measurement system is displayed. On each button the identification 
number of the transmitting Wi-Box AO transmitter is displayed. 

NOTE: All Wi-Box AO transmitters transmitting in the vicinity of the QUANTIEN 
measurement system will be displayed. Check that the correct Wi-Box unit is linked to 
the correct room when you configure each room; each Wi-Box unit has the 
corresponding identification number printed on the front. 

1.

 

To link a Wi-Box AO transmitter to a room, press first the 

Edit 

button, and then the 

Room 

button with the identification number of the correct Wi-Box AO transmitter. 

NOTE: The 

Edit 

button is not available to all users. Refer to User Settings for more 

information. (page 35) 

2.

 

Press the

 Name 

field and enter the 

Room

 name (maximum 8 characters). 

3.

 

Select 

Use as default

 if the QUANTIEN measurement system is placed permanently and 

this room should automatically be selected at startup. 

State: Released

  

Date: 2019.03.06 22:30 GMT

Содержание QUANTIEN





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды