manualshive.com logo in svg

St. Jude Medical QUANTIEN, Инструкция по эксплуатации

Поделиться
Скачать
St. Jude Medical QUANTIEN Скачать руководство пользователя страница 18

 

14 

 

 

Table 9.  Identification of Mains Cables 

Australia 

Rated Voltage: 250 V 
Rated Current: 2.5 A 

 

NOTE: If a cable needs to be replaced the cord set shall fulfill applicable regulations. If 
in doubt please contact St. Jude Medical. 

CAUTION: For markets other than those specified in the table above, make sure 
the chosen cord set fulfills applicable regulations. 

To be able to mount and install the QUANTIEN main unit, a mounting bracket is required. Use 
brackets supplied separately from St. Jude Medical or use an existing bracket compatible with 
standard VESA 75 x 75 mm or 100 x 100 mm. Refer to the Placement Options table for possible 
mounting solutions. 
Before proceeding with installation, check that all parts are undamaged. 

Mount QUANTIEN™ Main Unit in the Cath Lab 

WARNING: 

 

Make sure the equipment is securely mounted. If the equipment is not 

securely attached, it may fall over causing possible patient or operator injury 
and damage to the system. 

 

Do not use the QUANTIEN™ measurement system if it has been dropped or 

in any other way exposed to mechanical or electrical damage. This can cause 

the user or patient to be exposed to electric shock or cause faulty readings of 
data. Contact St. Jude Medical representatives or technical support for 
further instructions. 

 

Do not use the QUANTIEN measurement system if there is reason to believe 

the system's security has been compromised or if the system was 
unaccounted for a period of time (i.e. misappropriated, modified or tampered 
with). 

 

To protect the privacy and security of sensitive information, including 

electronic protected health information (EPHI), and to protect the integrity of 

the system itself, the system should be located in a physically secure, access 
controlled environment. 

CAUTION: Make sure a power cable with a connector suitable for the mains power 
outlet is used. Verify that the chosen cord set fulfills applicable ratings and 
regulations. 

St. Jude Medical recommends the QUANTIEN measurement system is installed in a secure, 
access controlled environment. If the QUANTIEN measurement system is not permanently 
mounted, it should be stored in a secured, access controlled location. 
The design of the QUANTIEN measurement system allows flexible placement either inside or 
outside the patient environment with fast and easy setup regardless of position. The placement in 
the cath lab will impact which devices, wireless or wired, can be connected. Benefits and 
limitations for different placement are summarized in the table below. 

State: Released

  

Date: 2019.03.06 22:30 GMT

Содержание QUANTIEN





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды