manualshive.com logo in svg

shelolab SRI21D, Руководство по установке и эксплуатации

Поделиться
Скачать
shelolab SRI21D Скачать руководство пользователя страница 7

7 | 

P a g e

 

INTRODUCTION 

 

 

 

T

EMPERATURE 

R

EFERENCE 

S

ENSOR 

D

EVICE

 

 

Must be purchased separately 

 

A reference sensor device is required for calibrating the incubator temperature display. 

Reference devices must meet the following standards: 

•

 

Accurate to at least 0.1°C 

The device should be regularly calibrated, preferably by a third party.  

 

Temperature Probe 

Use a digital device with a wire thermocouple probe that can be introduced into the incubation chamber 

through the unit access port. Select a thermocouple suitable for the application temperature you will be 

calibrating at. 

 

Why a Probe? 

Reference readings taken outside the chamber using wire temperature probes avoid chamber door 

openings. Openings disrupt the chamber temperature. Each disruption requires 

a minimum 1-hour wait 

to allow the atmosphere to re-stabilize before continuing. 

 

No Alcohol or Mercury Thermometers 

Alcohol thermometers do not have sufficient accuracy to conducti accurate temperature calibrations. 

Never place a mercury thermometer in the incubation chamber! 

Always use thermocouple probes. 

Temperature Reference 

Содержание SRI21D







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды