shelolab SRI21D Скачать руководство пользователя страница 48

Страница: 48 / 70

48 |

P a g e

USER MAINTENANCE

Continued on next page

Temperature Display Calibration – Day Temperature

Once the day temperature has stabilized, compare the reference device

temperature reading and the reading of the chamber controller.

If the readings are the same, or a difference between the two falls

within the acceptable range of your protocol, the display is

calibrated for day temperature.

Advance to the Calibrating the

Night Temperature steps starting on page 52.

- OR -

If a difference falls outside your protocol range, advance to the

next step.

Reference Device



A display calibration offset must be entered to match the current display

value to the reference device reading.

Reference Device



Determine the offset value and write down for use in Step 5.

•

The offset value is the difference between the reference device

reading and the reading of the chamber controller temperature

display.

Reference Sensor

Reading

Controller

Display

Offset

Value

23.0°C

22.0°C

1.0

21.2°C

22.0°C

-0.8

Reference Device



Offset Value: -0.8

Navigate to the Operations menu page.

Push and hold

both

the Up and Down Arrow Button

simultaneously for approximately 5 seconds.

Note:

Holding down both arrows for 10 seconds will open a Set menu

for setting memory parameters. If this happens, press the Reset

button to return to the Home page, the begin this step again.

Operations Menu

Содержание SRI21D







































































Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды

shelolab SRI21D, Руководство по установке и эксплуатации

Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды