shelolab SRI21D Скачать руководство пользователя страница 39

Страница: 39 / 70

39 |

P a g e

OPERATION

Note:

The auto day – night cycle will not launch until the start time of the next day phase is reached.

AUNCHING THE

IGHT

YCLE

Carryout the following steps to set the Day – Night Cycle to launch:

Press and briefly hold the EZ1 button.

•

After a brief pause, a red graph icon will illuminate on the right side of the controller

home page.

•

The controller will wait until the start of the next Day Phase

to adjust the lighting and

temperature of the cultivation chamber.

•

The cycle will run until terminated by an end user.

To terminate

the Cycle, briefly press and hold the EZ1 button. After a short pause, the red graph icon

will turn off. The Cycle has now ended.

CCESSORY

OMPATIBILITY AND

OWER

UTLET

The SRI21D is provided with a 115 voltage, 1 amp power outlet inside the chamber. Do not attach

powered equipment that draws more than 1 amp.

Verify that any powered accessory equipment used inside the chamber can safely and effectively

operate within your selected temperature range. Powered equipment types such as stirrers or

shakers, can generate heat sufficient to disrupt the thermal uniformity and stability of the chamber.

Figure 10: Home Page

Cycle operating in the day phase

The 2 indicates that the day

illumination lights are active

Содержание SRI21D







































































Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды

shelolab SRI21D, Руководство по установке и эксплуатации

Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды