shelolab SRI21D Скачать руководство пользователя страница 15

Страница: 15 / 70

15 |

P a g e

INSTALLATION

OWER

OURCE

EQUIREMENTS

When selecting a location for the unit, verify that each of the following requirements is satisfied.

Power Source:

The power source must match the voltage and ampere requirements listed on the

unit data plate. These units are intended for

115 VAC

50/60 Hz applications at

9 amps

•

Supplied voltage must not vary more than 10% from the data plate rating

. Damage to the

unit may result if supplied voltage varies more than 10%.

•

Wall power sources must be protective earth grounded.

•

Use a separate circuit to prevent loss of product due to overloading or circuit failure.

•

The wall power sources must conform to all national and local electrical codes.

Power Cord:

The unit must be positioned so that all end-users can quickly unplug the power cord in

the event of an emergency.

•

The unit is provided with an integral 125V, 15 Amp, NEMA 5-15P, 8ft (2.5m) power cord.

Circuit Breaker:

The unit is provided with an integral circuit breaker to protect against overcurrent

conditions.

•

Always determine the cause of an overcurrent event before resetting a tripped circuit

breaker.

IFTING AND

ANDLING

The unit should only be lifted by its bottom surfaces using proper heavy lifting machinery such as a

forklift or pallet jack.

•

Handles and knobs are inadequate for lifting or stabilization.

•

The unit should be completely restrained from tipping during lifting.

•

Transporting the unit while lifted is not recommended and may be hazardous.

•

Secure the door in the closed position prior to lifting the unit.

•

Do not attempt to move the unit while in operation or before the unit has cooled.

Содержание SRI21D







































































Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды

shelolab SRI21D, Руководство по установке и эксплуатации

Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды